25
Trouble Shooting
Trouble
Probable Cause
Suggested Remedy
1. FAN WILL NOT START
1.
Fuse or circuit breaker blown.
2.
Loose power line connections to the fan, or loose
switch wire connections in the switch housing.
1.
Check main and branch circuit fuses or circuit
breakers.
2.
Check line wire connections to fan and switch wire
connections in the switch housings.
CAUTION: Make sure main power is turned off !
3.
Replace with fresh battery.
2. FAN SOUNDS NOISY
1.
Blades not attached to fan.
2.
Loose screws in motor housing.
3.
Screws securing fan blade holders to motor hub are
loose.
4.
Wire connectors inside housing rattling.
5.
Motor noise caused by solid state variable speed
control.
6.
Screws holding blades to blade holders are loose.
1.
Attach blades to fan before operating.
2.
Check to make sure all screws in motor housing are
snug (not over-tight).
3.
Check to make sure the screws which attach the fan
blade holders to the motor hub are tight.
4.
Check to make sure wire connectors in switch
housing are not rattling against each other or against
the interior wall of the switch housing.
CAUTION: Make sure main power is turned off !
5.
Some fan motors are sensitive to signals from
solid-state variable speed controls. Solid-state controls
are not recommended, choose an alternative control
method.
6.
Tighten screws securely.
3. FAN WOBBLES
EXCESSIVELY
1.
Setscrew and nut in downrod support is loose.
2.
Setscrew in downrod/hanger ball assembly is loose.
3.
Screws securing fan blade holders to motor hub are
loose.
4.
Blade holders not seated properly.
5.
Hanger bracket and/or ceiling outlet box is not
securely fastened.
6.
Fan blades out of balance.
1.
Tighten both setscrews and nuts securely in downrod
support.
2.
Tighten the setscrew in the downrod/hanger ball
assembly.
3.
Check to be sure screws which attach the fan blade
holders to the motor hub are tight.
4.
Check to be sure the fan blade holders seat firmly
and uniformly to the surface of the motor housing. If
holders are seated incorrectly, loosen the screws and
retighten.
5.
Tighten the hanger bracket screws to the outlet box,
and secure outlet box.
6.
Interchanging position of fan blades can redistribute
the weight and result in a smoother operation. For
example, exchange blades in positions 1 and 3 or 1 and
4. If this does not improve wobble, exchange 2 and 4 or
2 and 5.
4. NOT ENOUGH AIR
MOVEMENT
1.
If possible, consider using a longer downrod.
(not included, you can buy the longer downrod from
fanimation.com).
WARNING
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.
3.
Dead battery in remote control.
Maintenance
How to Clean Your Ceiling Fan Blades
1.
y
l
n
o
e
h
t
s
i
n
a
f
g
n
il
i
e
c
w
e
n
r
u
o
y
f
o
g
n
i
n
a
e
l
c
c
i
d
o
i
r
e
P
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
.
h
s
i
n
i
f
e
h
t
g
n
i
h
c
t
a
r
c
s
d
i
o
v
a
o
t
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Periodic light dusting of the blades is recommended.
A feather duster will work best.
Avoid using water, cleansers, or harsh rags, which can
warp and ruin the blades.
CAUTION
Do not use solvents when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of electrical shock.
RECOMENDED:
Periodically check that the blade holders to motor hub screws are secure and tight.
