background image

9

Maintenance

Blade Cleaning

Periodic cleaning of your new ceiling fan is the only 
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth to 
avoid scratching the 

fi

 nish.

Abrasive cleaning agents are not required and should be 
avoided to prevent damage to 

fi

 nish.

Periodic light wiping of the blades is recommended.
A feather duster will work best.

Avoid using cleansers, or harsh rags, which can warp and 
ruin the blades.

CAUTION

Do not use solvents when cleaning your ceiling fan. It 

could damage the motor or the blades and create the 

possibility of electrical shock. 

RECOMENDED: 

 Periodically check that the blade holders to motor hub screws are secure and tight.

Operating Instructions - Pull Chain

1.

 Restore electrical power to the outlet box by turning the 

electricity on at the main fuse box.

2. 

Check the operation of the fan by gently pulling on the 

pull chain switch. (Figure 1)

3. 

If airflow is desired in the opposite direction, turn the 

fan off and wait for the blades to stop turning. Then slide 
the reverse switch to the opposite position and turn fan 
on again. Your fan model is equipped with a 4-position, 
3-speed, pull chain switch. The operating sequence is as 
follows:
 

1st Pull = HIGH  

3rd Pull = LOW

 

2nd Pull = MEDIUM 

4th Pull = OFF

Figure 1

Reversing

Switch

Speed Control

Pull Chain

R

EVERSE

 S

WITCH

 I

NFORMATION

S

EASON

R

OTATION

 D

IRECTION

S

WITCH

 P

OSITION

Summer

Counter-Clockwise

Right

Winter

Clockwise

Left

Summary of Contents for Edgewood TF900 Series















Reviews: