background image

12

Parts List

Models #HF6050**, #HF6200**, #HF6600**

Before discarding packaging materials, be certain all parts have been removed

¾¾

Insert FINISH CODES (Refer to fan model number located on downrod support)

How To Order Parts

Contact your retail store for repair parts.

When ordering repair parts, always

give the following information.

• Part Number

• Part Description

• Fan Model Number

Ref. #

Description

Part #

Standard Fan Assembly

HF6050

¾¾

Leaf Fan Assembly

 (for LK info, see pages 14 & 15)

HF6200

¾¾

with 

LKHF7260

¾¾

Presidio Tryne™ Fan Assembly

 (for LK info, see pages 16 & 17)

HF6600

¾¾

with 

LKHF7660

¾¾

STANDARD  FAN  ASSEMBLY  —  HF6050**

1

Hanger Bracket Assembly

APG610BL

2

Ball/Downrod Assembly

ADR1-6

¾¾

3

Downrod Cover Assembly

AP7070

¾¾

4

Ceiling Canopy

P7080

¾¾

5

Motor Coupler Cover

AP1115

¾¾

6

Fan Motor Assembly

AMA6050

¾¾

7

Blade Holder Set (5)

AP7030

¾¾

8

Wood Blade Set (5); Coffee or Slate

AP7052

¾¾

9

Switch Cup Cover Assembly

AP7020

¾¾

10

Receiver Unit

AP7075

11

Remote Control

C20

12

Support Cable Bag Containing:

HDWFP7000BL

Ceiling Support Cable

Cable Clamp

Flat Washer

Lag Bolt, 

3

/

8

˝

 x 2

˝

Loose Parts Hardware Bag Containing:

5

/

32

˝

 Threaded Rods (2)

5

/

32

˝

 External Lockwasher (2)

Knurled Knobs (2)

5

/

32

˝

 x 19mm Flat Head Screws (2)

Wire Nut (4)

Balance Kit

Blade Mount Hardware Bag Containing:

3

/

16

˝

 Pan Head Screw with Washer Head (16)

Fiber Washer (16)

Phillips Screwdriver, 4

˝

Blade Holder Mount Hardware Bag Containing:

¼

˝

 Pan Head Screw (11)

Summary of Contents for HF6050 Series





















Reviews: