background image

6

How to Hang Your Ceiling Fan

1.

  Securely attach the hanger bracket to the outlet box 

using the outlet box screws and washers supplied with the 
outlet box (Figure 6).

NOTE:

 

 Outlet box screws pass through slotted holes of 

the hanger bracket (Figure 6).

2.

   Pull the electric wires in the outlet box down through 

the opening in the hanger bracket and bend wires up and 
out of the way so that the hanger ball will easily fit into the 
hanger bracket. 

3.

   Carefully lift the fan and seat the downrod/hanger ball 

assembly on the hanger bracket that was just attached to 
the outlet box (Figure 7).  Be sure the groove in the ball is 
lined up with tab on the hanger bracket (Figure 6).

Figure 7

Figure 6

Figure 5

Outlet Box

Hanger

Bracket

Outlet Box

Hanger

Bracket

Screw (2)

Supplied with

Outlet Box

Tab

Floor

Ceiling

No

less than

7 ft

Downrod/Hanger

Ball Assembly

WARNING

The fan must be hung with at least 7´ of clearance from 

floor to blades (Figure 5)

WARNING

The outlet box must be securely anchored and capable 

of withstanding a load of at least 50 lbs.  Hanger bracket 

must seat 

fi

 rmly against outlet box.  If the outlet box is 

recessed, remove wallboard until bracket contacts box.  

If bracket and/or outlet box are not securely attached, 

the fan could wobble or fall.

CAUTION

Do not connect fan blades until the fan is completely 

installed.  Hanging fan with blades connected may result 

in damage to the fan blades.

WARNING

Failure to seat tab in groove could cause damage to 

electrical wires and possible shock or fire hazard.

WARNING

To avoid possible shock, do not pinch wires between the 

downrod/hanger ball assembly and the hanger bracket.

INSTALLATION NOTE

If C4 Remote Control (optional) is desired, a Remote Receiver Unit must be installed (after setting the code) in the Hanger 

Bracket prior to wiring your ceiling fan. See page 8 

WARNING

To avoid possible electrical shock, be sure electricity is 

turned off at the main fuse box before hanging.

NOTE: If you are not sure if the outlet box is grounded, 

contact a licensed electrician for advice, as it must be 

grounded for safe operation.

Summary of Contents for Louvre FP1320 Series

















Reviews: