Fanimation Louvre FP1320 Series, Owner'S Manual

OFF

HI

LO

MED

8

How to Wire Your Ceiling Fan - C4 Hand-held Remote (Optional)

Operating Instructions - C4 Hand-held Remote (Optional)

1.

 Operating & Using Remote Transmitter (Figure 13):

Install 9 volt battery (If not using for long periods of time, 
remove battery to prevent damage to transmitter). Store 
the transmitter away from excess heat or humidity.

1. Setting the Code: 

The remote unit has 16 different 

code combinations. To prevent possible interference from 

or to other remote units such as garage door openers, car 

alarm or security systems, simply change the combination 

code in your transmitter and receiver. To set the code, 

perform these steps.

• Transmitter:

 remove battery cover. Press firmly below 

arrow and slide battery cover off.  Slide code switches to 

your choice of up or down position.  Factory setting is all 

up. Do not use this position. With a small screwdriver or 

ball point pen slide firmly up or down (Figure 10a). Replace 

battery cover on the transmitter.

• Receiver: 

 Slide code switches to the same positions 

as set on your transmitter (Figure 10b).

If you feel that you do not have enough electrical wiring 

knowledge or experience, have your fan installed by a 

licensed electrician. 

2. Installing Receiver in Hanger Bracket:

• Slide remote Receiver into the Hanger Bracket (Fig-

ure 11).

• Connect wires as indicated: (Figure 12)

– Green Hanger Bracket and Hanger Ball wires to 

BARE (ground) wire.

– BLACK Receiver Unit wire (AC IN L) to BLACK sup-

ply wire.

– WHITE Receiver Unit wire (AC IN N). to WHITE sup-

ply wire.

– WHITE Receiver Unit wire (TO MOTOR N) to WHITE 

fan wire.

– BLACK Receiver Unit wire (TO MOTOR L) to BLACK 

fan wire.

– BLUE Receiver Unit wire (FOR LIGHT DOWN) to 

BLUE light wire.

• Position all connected wires and receiver antenna to 

allow installation of ceiling canopy.

• To install ceiling canopy, see page 10.

• Restore electrical power.

NOTE:

 If fan or supply wires are different colors than indicated, 

have this unit installed by a quali

fi

 ed electrician. 

NOTE:

  Set pull chain to high speed before using the 

remote control.  To avoid accidental pull chain use, 
shorten chain by cutting it 2 to 4 inches below switch body. 
You can now use your speed control to select any of the 
3-speeds plus OFF.

• HI Push Button – high fan speed

• MED Push Button – medium fan speed

• LOW Push Button – low fan speed

• OFF Push Button – fan off

• Light Push Button – no function (unless light kit is 

installed)

Figure 11

Figure 12

Figure 10b

Figure 10a

Figure 13

Receiver Unit

Ceiling

Bracket

(Open End)

BLK-ANT

BL-AC IN L

WH-AC IN N

BLUE-FOR LIGHT DOWN

BLK-TO MOTOR L

WH-TO MOTOR N

GRN or BARE GROUND

GRN from hanger ball

GRN from bracket

9V

Battery

Remote Transmitter

Unit Detail

Reciever Unit Detail

9V

Battery

120 VAC SUPPLY

(User Supplied)

NOTE:

 Receiver wires omitted for clarity. 

▲

WARNING

Check to see that all connections are tight, including 

ground, and that no bare wire is visible at the wire 

connectors, except for the ground wire.  Do not operate 

fan until the blades is in place.  Noise and fan damage 

could result.

▲

WARNING

To avoid possible electrical shock, be sure electricity is 

turned off at the main fuse box before wiring.

NOTE: If you are not sure if the outlet box is grounded, 

contact a licensed electrician for advice, as it must be 

grounded for safe operation.