3
This Manual is Designed to Make it as Easy as Possible for You
to Assemble, Install, Operate, and Maintain Your Ceiling Fan
Unpacking Instructions
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
steps have been completed and will be helpful in
fi
nding your place should you be interrupted.
Wiring outlet box and box connectors must be of type
required by local code. The minimum wire would be a 3-
conductor (2-wire with ground) of the following size:
NOTE:
Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are missing,
contact your local retailer.
Tools Needed for Assembly
Materials
• One Phillips head screwdriver
• One stepladder
• One ¼˝
blade screwdriver
• One wire stripper
•
Three wire connectors
(supplied)
•
7
⁄
16
˝
,
½
˝
&
9
⁄
16
˝
wrench
or socket wrench
DAMP LOCATION CEILING FAN:
If you have purchased a
Damp Location Ceiling Fan, you may only use light kits marked
suitable for use in damp locations.
Wire Size A.W.G.
Installed Wire Length
14
12
Up to 50 ft.
50 - 100 ft.
NOTE:
If you are uncertain of part description, refer to
exploded view illustration. (Figure 1, page 15)
1.
Check to see that you have received the following
parts:
•
Horizontal Tube Assembly
•
Two Motor Assemblies
• Blade Holder pack containing:
– Four blade holders (red dot)
– Four blade holders (white dot)
– Eight blade arm covers
• Blade Cover Mount’g Hardware Bag
– Seventeen
3
⁄
16
˝
–24 x
3
⁄
8
˝
screws
– Fanimation screwdriver
• Blade to Hub Mount’g Hardware Bag
– Seventeen 10–32 x ½
˝
screws
• Hanger Ball
Adapter Assembly
• Ceiling Canopy
• Hanger Bracket
Assembly
• 2-speed, CW3 wall control
Ceiling
Canopy
Hanger Bracket
Assembly
2-speed
CW3 Wall Control
Hardware Bag
Blade Holder
Packs (2 sets)
Side B
Side A
Horizontal
Tube Assembly
Blade Mounting
Hardware Bag
NOTE:
The illustration shown is not to scale or its actual con
fi
guration may vary, wires partially removed for clarity.
NOTE:
An (24
˝
, 30
˝
, 36
˝
or other available various lengths)
extension pole is required for installation. Extension poles must
be purchased separately.
Hanger Ball
Adapter
Assembly
Support Cable
Bag
Motor Assembly (2)
• Support Cable bag:
– Ceiling Support Cable
– Cable Clamp
– 5
˝
lag bolt
– 2
˝
lag bolt
–
3
⁄
8
˝
flat washer
• Hardware bag:
– 2
˝
lag bolt
– 5 mm allen wrench
– Four ¼˝
–20 x ½
˝
screws
– Two
5
⁄
32
˝
–32 x 1
˝
threaded rods
– Two
5
⁄
32
˝
–32 external lockwashers
– Two
5
⁄
32
˝
knurled knobs
– Six motor mounting screws
– T
wo ¼˝
–20 x 2
1
⁄
8
˝
cap head bolts
– T
wo ¼˝
–20 nylon lock nuts
– Four wire connectors
▲
WARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
▲
WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 8). If you feel you
do not have enough wiring knowledge or experience,
have your fan installed by a licensed electrician.
NOTE: Assemble with Hand tools Only!
