background image

9

How to Wire Your Ceiling Fan - Pull Chain

If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a 
licensed electrician. 

1.

 Connect the green grounding lead from the hanger ball 

and the green grounding lead from the hanger bracket to 
the supply grounding conductor (this may be a bare wire 
or wire with green colored insulation). Securely connect 
wires with wire connectors supplied.

2.

 Securely connect the white fan motor wire to the white 

supply (neutral) wire using wire connector supplied. 

!

Securely connect the black fan motor wire and blue wire 
to  the black supply wire using wire connector supplied 
(Figure 1). 

3.

After  splicing and making the wire connections, the 

wires should be spread apart and turned upward with 
the  grounded conductor and the equipment-grounding 
conductor on one side of the outlet box and the ungrounded 
conductor on the other side of the outlet box.

4.

 Secure the ceiling canopy to the hanger bracket with 

threaded  rods, external lockwashers, and knurled knobs 
provided (see below). 

Household
Supply

Listed
Outlet Box

Black

Green Wire

(Ground) from

Hanger Bracket

Green Wire

(Ground)

Black

Fan Wire

White

Blue

Green Wire

(Ground) from

Hanger Bowl

Figure 1

ʆ

WARNING

To avoid possible electrical shock, be sure electricity is 
turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded, 
contact a licensed electrician for advice, as it must be 
grounded for safe operation.

ʆ

WARNING

Check to see that all connections are tight, including 
ground, and that no bare wire is visible at the wire 
connectors, except for the ground wire.  Do not operate 
fan until the blades are in place.  Noise and fan damage 
could result.

Installing the Canopy Housing

1.

 Screw in two threaded rods into the Hanger Bracket 

(Figure 1a).

NOTE:

 The threaded rods in the hanger bracket serves as 

guides for easier installation.

2.

 Securely attach the Canopy Housing to the Hanger 

Bracket using the external lockwashers and knurled knobs 
supplied with your fan (Figure 1b).

Figure 1a

Figure 1b

NOTE:

 Supply wires and fan wires omitted for clarity. 

NOTE:

!

 This step is applicable 

after

 the neccessary wiring 

is completed.

ʆ

WARNING

To avoid possible fire or shock, make sure that the 
electrical wires are completely inside the canopy housing 
and not pinched between the housing and the ceiling.

Summary of Contents for The Levon FP7910 series

































Reviews: