background image

1.   Read your owner's manual and safety information before installing your new fan.  Review the accompanying assembly

      diagrams.

2.   Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent

      power from being switched on accidentally.  When the service disconnecting means cannot be locked, securely fasten a

      warning device, such as a tag, to the service panel.

3.   Be careful of the fan and blades when cleaning, painting, or working near the fan.  Always turn off the power to the ceiling

      fan before servicing.

4.   Do not insert anything into the fan blades while the fan is operating.

5.   Do not operate reversing switch until fan blades have come to a complete stop.

Important Safety Instructions 

Additional Safety Instructions

WARNING: To avoid fire, shock and serious personal injury, follow these instructions.

1.   To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.

2.   All wiring must satisfy National (ANSI/ NFPA) Electrical Codes.  Use the National Electrical Code if Local Codes do not

      exist.  The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made

      or approved by a licensed electrician.

3.   The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 lbs. (fan and accessories not to

      exceed 35 lbs. or 17 kgs.).  Use only UL outlet boxes listed as acceptable for fan support.  Most outlet boxes commonly used

      for support of light fixtures are not acceptable for fan support and may need to be replaced.  Consult a qualified electrician if in

      doubt.

4.   

CAUTION:

  To reduce the risk of personal injury, mount the hanger bracket to an outlet box marked "Acceptable For Fan

      Support" using the hardware provided with your fan or the outlet box.

5.   The downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for an 8 foot ceiling.

6.   The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

7.   Follow the recommended instructions for the proper method of wiring your ceiling fan.  If you do not have adequate electrical

      knowledge or experience, have your fan installed by licensed electrician.

WARNING:

  To avoid fire, shock or injury, do not use a control not specifically approved for this fan.

WARNING:

  This product is designed to use only those parts supplied with this product and/or accessories designated specifically for 

use with this product.  Using parts and/or accessories not designated for use with this product could result in personal injury or 

property damage.

*

 

WARNING:

  To reduce the risk of personal injury, do not bend the blade flange (blade holder) when installing, balancing, or 

cleaning the fan.  Do not insert foreign objects in between rotating fan blades.

1.   

LIMITED LIFETIME MOTOR WARRANTY

 - If any part of your fan motor fails, due to a defect in materials or workmanship during the 

      lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective fan is returned to our national

      service center.  Proof of purchase is required.  Customer shall be responsible for all costs incurred in the removal or reinstallation and shipping 

      of the product for repairs or replacement.

2.   

ONE YEAR MOTOR LABOR WARRANTY

 - If your fan motor fails at any time within one year from the original purchase, due to defects

      in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center.  Purchaser will be

      responsible for labor charges after this one-year period.  Customer shall be responsible for all costs incurred in the removal or reinstallation and

      shipping of the product for repairs or replacement.

3.   If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we will 

      repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.

4.   Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding, tarnishing, or 

      peeling.

5.  This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of heat or 

      humidity, or as a result of any modification to the original product.

6.   All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan or 

      Fanimation.

7.   Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.

8.   Under no circumstances may a fan be returned without prior authorization from Fanimation.  The receipt of purchase must accompany 

      authorized returns and must be sent freight prepaid to Fanimation.  The fan to be returned must be properly packed to avoid damage in transit; 

      Fanimation will not be responsible for any damage resulting from improper packaging.

9.   It is understood that any repair or replacement is the exclusive remedy available from Fanimation.  There is no other expressed or implied 

      warranty.  Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and fitness for a 

      particular purpose to the extent permitted by law.  Some states do not allow limitations on implied warranties.  Fanimation will not be liable for

      incidental, consequential, or special damages arising out of or in conjunction with product use or performance, except as may otherwise be 

      accorded by law.  This warranty gives you special legal rights and you may also have other rights that vary from state to state.

10. A certain amount of wobble is normal and should not be considered a problem or a defect.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

*

 DAMP LOCATION CEILING FAN:  

For a Damp Location Ceiling Fan, you may only use light kits marked suitable for use in damp locations. 

Summary of Contents for Tropicana FP1600 Series











































Reviews: