Rev.23
40/311
4.9.
Function 59N_1 and 59N_2. Definite-time neutral overvoltage
This protection function is adjusted using three parameters:
Function
Description
Minimum
Maximum
Step
Unit
Default
59N_1
59N_2
Definite-time neutral overvoltage
Permission
-
-
Yes/No
-
No
Pickup
4
170
1
V
10
Operating time
0.02
300.00
0.01
s
100
Reset time
0.2
1200.0
0.1
s
0.2
The operating time is completely independent of the measured neutral voltage, such that should the
neutral voltage exceed the set value during the same amount of time or more than the set one during
operation time, the protection function acts (trips) and there it is not restored until the measured value
of the neutral voltage drops below the voltage set point during adjusting reset time.
The function pick up occurs at 100% of the adjusted input and the dropout at 95%. The reset type is
temporized and reset time is adjusted with reset time parameter.
The accuracy of the operating time is the adjusted time ±30ms.
NB: The neutral voltage is obtained internally in the equipment, using the sum of the 3-phase voltages.
4.10. Function 27_1 and 27_2. Definite-time phase undervoltage
This protection function is adjusted using three parameters:
Function
Description
Minimum
Maximum
Step
Unit
Default
27_1
27_2
Definite-time phase undervoltage
Permission
-
-
Yes/No
-
No
Pickup
4
170
1
V
50
Operating time
0.02
300
0.01
s
100
Reset time
0.2
1200.0
0.1
s
0.2
The operating time is completely independent of the measured phase voltage, such that should the
phase voltage goes down the set value during the same amount of time or more than the set one, the
protection function acts (trips) and there it is not restored until the measured value of the phase voltage
exceeds the voltage set point during adjusting reset time.
The function pick up occurs at 100% of the adjusted input and the dropout at 105%. The reset type is
instantaneous temporized and reset time is adjusted with reset time parameter.
The accuracy of the operating time is the adjusted time ±30ms.
Summary of Contents for SIL B
