background image

Sunbury Nursery Furniture 

4/56 Cambridge Street, Coorparoo,
Qld 4151

Phone: 07 3847 3699, 
Fax: 07 3397 1146
E-mail: sales@sunburynursery.com.au

WARNINGS
PLEASE ENSURE THE INSTRUCTIONS ARE FOLLOWED CAREFULLY TO ENSURE 
THE SAFETY OF THIS COT IS NOT COMPROMISED:

Dispose of any wrapping immediately to avoid danger of suffocation.
Ensure the enclosed assembly instructions are followed in detail.
Ensure the cot is placed at a reasonable distance from curtains, blinds, heaters and power 
points.
Keep medication, string, elastic, small toys and small items such as money out of reach 
from any position in the cot. 

WARNING: TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE 
ADJUSTED TO THE LOWEST POSITION BEFORE THE CHILD CAN SIT UP.

In case of the cot being damaged in any way, please do not continue to use it, as this 
could  cause injury or harm.
Ensure that your child is clear of any moving parts when accessing the dropside.

Page 7

Ensure that your child is clear of any moving parts when accessing the dropside.
Ensure the wheels have the brakes locked while the cot is in use.
When using the dropside, ensure you first lift and then push the pins at either end 
simultaneously. This dropside can be lifted using 1 or 2 hands. Ensure that the dropside 
locks into the upper position when raised.
RECOMMENDED MATTRESS SIZE: This cot has been manufactured for use with a 
mattress which measures 690mm wide x 1300mm long and 120mm in thickness. The 
width and length are specified because it is important that the gaps between the mattress 
and the sides and ends of the cot will not exceed 40mm. This is to minimise the risk of a 
child’s limb becoming caught in the gap. The thickness of the mattress has been specified 
to ensure that the depth of the cot is greater than 500mm with the mattress base in the 
lower position to minimize the risk of a child climbing or falling out of the cot.
Please retain your sales receipt for proof of purchase and warranty.

Summary of Contents for SUNBURY








Reviews: