7
CARE AND MAINTENANCE
To improve the performance and life of your unit, we recommend you do the
following:
1. Once a month clean the unit with a dry cloth, including the chamber which the dust
container fits into. Remove any hair, fiber or other materials that may have built up
in the chamber, on the rotating brush.
2.
Don’t
use abrasive materials to clean the sweeper.
Do not immerse the unit in
water.
3.
Do not
pick up liquids or use on wet floors.
4.
Do not
use on concrete, tar or similar rough surfaces.
5.
Don’t
pick up pieces of string or fabrics with the sweeper.
6.
Do not
clean tasseled or frayed carpets with the sweeper.
STORING THE CORDLESS SWEEPER
Your cordless sweeper may be stored by using the slot on the back of the upper handle
and hanging it from a screw secured to a wall or other vertical surface. Use a #6 flat or
pan head screw with the appropriate hardware for the surface that the sweeper will be
mounted on, (i.e. gyproc). Allow the screw head to extend a approximately 3/16" from
the mounting surface. Always empty your sweeper before hanging up for storage.
OPERATING INSTRUCTIONS
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE
REASON
POSSIBLE
SOLUTION
SWEEPER WILL
NOT OPERATE
1. Batteries
discharged.
2. No power in electrical
outlet supplying charging
adapter.
3. Unit
needs
servicing.
4. Battery
misplaced.
1. Charge
unit.
2. Check fuse or breaker.
Replace fuse/reset breaker.
3. Call
Customer
Service.
4. Match “+” on battery to
compartment “+”.
SWEEPER WILL
NOT PICK-UP
1. Dust container is full.
2. Unit
needs
recharging.
1. Empty dust container.
2. Charge
unit.
DUST ESCAPING
FROM SWEEPER
1. Dust container is full.
1. Empty dust container.
ROTATING BRUSH
WILL NOT PICK UP
1. Unit
clogged.
2. Dust container is full.
1. Check for excessive material
on brush or in bottom of
sweeper. Remove obstruction
from brushes and/or sweeper.
2. Empty and clean dust
container.
SWEEPER WILL
NOT CHARGE
1. Electrical outlet not
working.
2. Charging
Adapter
not
working.
3. Batteries no longer
functioning.
4. Unit left in “On” position.
1. Check to ensure outlet is
working properly. (Easily
checked by plugging in
another appliance.
2. Replace
charging
adapter.
3. See battery disposal.
4. Press switch to “Off”.
18
REMARQUE:
Modèles de balayeuse sans fil expédiés avec des piles
non chargées. L’appareil doit être chargé pendant 20
heures avant la première utilisation. N’utilisez que les
piles de rechange X1725QN.
*Les illustrations peuvent différer du produit lui-même.
PIÈCES ET COMPOSANTES
1. Poignée
supérieure
2. Tubes de rallonge
(x2)
3.
Poignée inférieure du tube de rallonge
4.
Poignée inférieure
(
expédié à l’intérieur de la coupelle à poussière)
5.
Écrou et boulon captifs
(sur le pivot de la poignée inférieure)
6.
Témoin de chargement
7. Bouton
d’alimentation
On/Off
8.
Adaptateur de chargement: N’utilisez que le
modèle TechWorld AD-0815-U8,
7,5 volts-150mA
(expédié à l’intérieur de la coupelle à poussière)
9.
Coupelle à poussière
10. Couvercle de la brosse transparent
11. Brosse rotative
12. Électrobrosse balayeuse
Summary of Contents for FS1735Q
Page 2: ......
