background image

 

 

35

2). Fixed Length: the phone will intersect the number according to your specified length. 
3). Time Out: After you stop dialing and waiting time out, system will send the number collected. 
4).  User  defined:  you  can  customize  digital  map  rules  to  make  dialing  more  flexible.  It  is  realized  by 
defining the prefix of phone number and number length of dialing. 

 

In order to keep some users' secondary dialing manner when dialing the external line with PBX, phone can 
be added a special rule to realize it. Souser can dial a number as external line prefix and get the secondary 
dial tone to  keep  dial the  external  number.  After finishing  dialing, phone will send the prefix and  external 
number totally to their server. 
For example, there is a rule 9,xxxxxxxx in the digital map table. After dialing 9, phone will send the 
secondary dial tone, user may keep going dialing. After finished, phone will call the number which starts 
with 9; actually the number sent out is 9-digit with 

9.

 

 

Digital Map Configuration

 

Field name

 

explanation 

Press “#” to Send 

Set Enable/Disable the phone ended with “#” dial.   

Dial Fixed Length xx to 
Send 

Specify the Fixed Length of phone ending with. 

Send after xx second 

Set the timeout of the last dial digit. The call will be sent after 
timeout. 

Press # to Do Blind 
Transfer 

Enable Blind Transfer OnHook, when executing Blind Transfer 
End with #, press # after inputting the number that you want to 
transfer, the phone will transfer the current call to the third party 

Blind Transfer OnHook 

Enable Blind Transfer OnHook, when executing Blind Transfer, 
hang up after inputting the number that you want to transfer, the 
phone will transfer the current call to the third party 

Attend Transfer OnHook 

Enable Attend Trans OnHook, when executing Attended Transfer, 
hang up after the third party answers, the phone will transfer the 
current call to the third party 

Below is user-defined digital map rule: 
[] Specifies a range that will match digit. May be a range, a list of ranges separated by commas, 
or a list of digits. 
* Match any single digit that is dialed. 
. Match any arbitrary number of digits including none. 
Tn Indicates an additional time out period before digits are sent of n seconds in length. n is 
mandatory and can have a value of 0 to 9 seconds. Tn must be the last 2 characters of a dial 
plan. If Tn is not specified it is assumed to be T0 by default on all dial plans. 

Summary of Contents for C56



















































Reviews: