- 14 -
Mi 2446IGb
Tworzenie nowego aktuatora
Po wciœniêciu przycisku
“nowy aktuator”
pojawia siê strona
na ekranie
alfanumeryczna do wprowadzenia nazwy aktuatora - wprowadŸ nazwê
aktuatora (np..: “podlewanie”) i wciœnij przycisk “zapisz”; po pojawieniu
siê strony wprowadzania adresu - wprowadŸ adres aktuatora (np.: 211)
i wciœnij “zapisz”, powrócisz do strony pocz¹tkowej.
Uwaga:
W celu poprawnej pracy urz¹dzenia zapisz ten sam adres,
:
który zapisa³eœ w monitorze tak¿e w przekaŸniku 2281 za pomoc¹ któ-
rego chcesz realizowaæ okreœlone funkcje. Ustaw równie¿ bistabilny tryb
pracy przekaŸnika 2281 (patrz instrukcja przekaŸnika 2281).
Tryb pracy aktuatora
Aby zmodyfikowaæ tryb pracy aktuatora dotknij ikonê “Pod-
gl¹d” obok nazwy aktuatora którego ustawienia chcesz
modyfikowaæ; po tej operacji przejdziesz do strony
gdzie mo¿esz ustawiæ nastêpuj¹ce funkcje:
Rêczny
- dotknij przycisk “Rêczny”, aby ustawiæ aktuator w rêcz-
nym trybie pracy; szczegó³owy opis na stronach 44 i 45.
Auto
- dotknij przycisk “Automatyczny”, aby ustawiæ automaty-
czny tryb pracy aktuatora; szczegó³owy opis na stronach 44 i 45.
Do zdarzenia -
dotknij “Do zdarzenia”, aby ustawiæ aktuator
w trybie “do zdarzenia” (uwaga: jeœli aktuator jest ustawiony w trybie
“do zdarzenia” musi istnieæ w systemie logiczne zdarzenie przypi-
sane do aktuatora); szczegó³owy opis na stronach 44 i 45.
Stan -
ta ikona pokazuje stan aktuatora i staje siê czerwona jeœli
urz¹dzenie jest WY£¥CZONE lub zielona jeœli urz¹dzenie jest W£¥-
CZONE.
Uwaga: jeœli wewn¹trz zielonej ikony pojawia siê znak zapytania ozna-
cza to ¿e aktuator nie odpowiada na komendy z monitora myLogic
i w konsekwencji nie jest mo¿liwe odczytanie jego stanu; w tym
wypadku sprawdŸ adres aktuatora i jego pod³¹czenie do systemu;
Programowanie
(ustawienia) - po wciœniêciu tego przycisku przej-
dziesz do strony, która umo¿liwia zaprogramowanie nastêpuj¹cych
funkcji niezbêdnych do automatycznej pracy aktuatora:
-
Ustawienia dnia A -
godzinowe programowanie aktuatora
w automatycznym trybie pracy dla dnia A (patrz strona 45).
-
Ustawienia dnia B -
godzinowe programowanie aktuatora w
automatycznym trybie pracy dla dnia B (patrz strona 45).
-
Programowanie tygodnia -
tygodniowy rozk³ad pracy urz¹dzenia
w automatycznym trybie pracy (patrz strona 45).
-
Adres/Nazwa - m
odyfikacja nazwy i adresu aktuatora; po dotk-
niêciu
tlana jest nazwa
tej ikony przejdziesz do strony gdzie wyœwie
i adres aktuatora: dotknij przycisk “zmieñ” obok nazwy, aby zmieniæ
nazwê lub dotknij przycisk “zmieñ” obok adresu, aby zmieniæ adres.
Sposób wprowadzania znaków i
opisany
cyfr jest taki sam jak
w “Programowanie adresu,
nazwy u¿ytkownika, numeru poko-
ju”. Dotknij “zapisz”, aby zachowaæ dane i przejœæ z powrotem
do poprzedniej strony.
Usuñ aktuator
Aby usun¹æ aktuator wybierz go z listy przez
krótkie
wciœniêcie jego nazwy i nastêpnie dotknij przycisk “Usuñ
aktu
aktuator i pow-
ator”. Dotknij przycisk , aby usun¹æ
róciæ do poprzedniej strony.
Funkcje wewnêtrznych przekaŸników
2 wewnêtrzne przekaŸniki monitora myLogic s¹ zaprogra-
mowane fabrycznie do obs³ugi kontroli temperatury (prze-
kaŸnik 1) i dodatkowego dzwonka (przekaŸnik 2); po odpo-
wiednim zaprogramowaniu mog¹ byæ równie¿ u¿ywane do
innych funkcji.
Jak zaprogramowaæ wewnêtrzne przekaŸniki jako aktuatory
Programowanie wewnêtrznych przekaŸników jako aktuatorów w sy-
stemie jest podobne do programowania zewnêtrznego aktuatora
jednak ró¿ni siê tym ¿e adresy s¹ sta³e i nie mog¹ byæ zmienione: prze-
kaŸnik 1 jest zawsze programowany z adresem “i1” (”i” z du¿ej lub ma-
³ej litery), przekaŸnik 2 musi byæ zawsze zaprogramowany z adresem
Create a new actuator
After having pressed
“new actuator”
on the display appears the
alphanumerical page to insert the name – Insert the name of actuator
(e.g.: “watering”) and press “save”; after that will appear the page to
insert the addresses – Insert the address of the actuator (e.g.: 211)
and press “save”, you will be back to the initial page.
Note:
for a correct behaviour, store on the myLogic terminal the same
address you have or you will store on the relay of the actuator art. 2281
which you want to carry out the required function, on this device select
also the operating mode “bistable”
(see instructions of the art. 2281).
Operating mode of the actuator
To modify the operating mode of the actuator press the icon
“
Details
” near by the name of the actuator you wish to
modify, after this operation you will access to a menu
where it is possible to chose among:
Manual
- press “Manual” to set the actuator in manual operating
mode; more details are reported on the pages 44 and 45.
Auto
- press “Auto” to set the actuator in automatic operating mode;
more details are reported on the pages 44 and 45.
On event
– press “On event” to set the actuator in on event operating
mode (warning: if an actuator is set in “on event” operating mode it
must exist in the system an event logically related to that actuator);
more details are reported on the pages 44 and 45.
State
– this icon shows the state of an actuator and it can become
red if the device is OFF, or green if the device is ON;
Attention
: if
inside the green icon appears a question mark it means that the
actuator doesn’t answer to the commands of myLogic terminal and
consequently it is impossible to know its state; check the address
of the actuator and its connection to the system.
Programming
(settings) – by pressing this button you enter in a
page where it is possible to program the following functions for the
automatic operating mode of the actuator:
-
A day setting
- hourly programming of the actuator in automatic
operating mode for the day A (see page 45).
-
B day setting
- hourly programming of the actuator in automatic
operating mode for the day B (see page 45).
-
Week setting–
weekly programming of the device in automatic
operating mode (see page 45).
-
Address/Name
– it is possible to modify the name and the address
of an actuator, after pressing this icon you enter a page where the
name and the address of the actuator is shown; press the button
“modify” beside the name to change the name or the button “modify”
beside the address to modify the address. The operations to insert
characters and numbers are the same described for the
“Programming address, user name, room number”.
Press “save” to
store data and go back to the previous page.
Delete an actuator
To delete an actuator it is necessary to select it from a list
by pressing shortly the icon of the name, and than press
“Delete actuator” to delete it. Press
to delete the
actuator and go back to the previous page.
Functions of internal relays
The 2 internal relays of myLogic terminal are programmed
from the factory to carry out thermal control (relay 1) and
supplementary bell (relay 2); they can be used also for
other functions if properly programmed.
How to program the internal relays as actuators
The programming of the internal relays as actuators of the system is
similar to that of an external actuator the only difference is that the
addresses are fixed and can not be changed: the relay 1 will always
be programmed with the address
“i1” (with
“i” either lowercase or
uppercase), the relay 2 must always be programmed with the address
Details
Podgl¹d
Summary of Contents for myLogic ML2262C
Page 55: ... 55 Mi2446IGb Notatki Notes ...