Operation - 1370, 1385, 1395, 13114 Backsaver Auger
30
Reducing The PTO Driveline Length
Stop the engine and leave the operator’s position.
See
“Entering & Leaving The Operator’s Position”
Make sure the PTO driveline and all rotating
components have come to a complete stop before
leaving the operator’s position.
WARNING
AVOID INJURY OR DEATH
•
Do NOT exceed the rated implement PTO speed.
•
Stay clear of rotating driveline.
•
Keep bystanders away.
•
Keep hands, feet, clothing and long hair away.
•
Keep PTO shields and all guards in place.
•
Disengage PTO, move the tractor controls to the
Neutral position, stop the engine and make sure all
rotating components are stopped before leaving the
operator’s position.
•
Do NOT service the tractor or implement with the
PTO engaged.
•
Do NOT service the implement in a raised position
unless properly blocked and with all rotating
components stopped.
•
Disengage PTO for road travel.
Remove the PTO driveline from the tractor and
place in storage position (if equipped).
Enter the operator’s position (See “Entering The
Operator’s Position” in the Operation section).
Start the engine.
Raise or lower the three-point implement to get
the shortest distance between the tractor PTO
shaft and three-point implement gearbox PTO
shaft. Stop the engine and leave the operator’s
position.
Pull the PTO driveline apart and reinstall each
individual section; one half to the tractor PTO shaft
and one half to the implement gearbox PTO shaft.
Figure 13
1. Hold PTO driveline sections parallel to one another
and measure back 2 in. (50.8 mm) (Item 1) from the
yoke of each section and place mark on opposite
section. Cut the plastic shield at this length (Item 2)
Figure 14
2. Using the plastic guard lengths that were cut off in,
align the cut off lengths (Item 1) with the end of the
inner & outer shafts. Place a mark (Item 2) on the
inner & outer shafts and cut the inner & outer shafts
off at this length
3. Round off all sharp edges and debur.
4. Thoroughly grease and install the PTO driveline
halves together.
5. Recheck for proper operation.
TRACTOR
PTO SHAFT
IMPLEMENT
PTO SHAFT
2
1
1
2
TRACTOR
PTO SHAFT
IMPLEMENT
PTO SHAFT
2
2
1
Summary of Contents for 1370
