background image

2

Revision date: 08.15.12

CARTS AND WAGONS

READ THIS DOCUMENT BEFORE YOU BEGIN

Thank you for purchasing this heavy duty cart. When  

properly assembled and maintained, this product will  

provide years of reliable service. These instructions 

include helpful hints and important information needed to 

safely assemble and properly maintain the cart. Please 

read these instructions 

before

 you begin.

If you have any questions during the assembly, contact 

customer service for assistance. 

SAFETY PRECAUTIONS

• 

Do not

 use the cart if any part is broken or damaged.

• 

This cart is not a toy

Do not

 allow children to use the 

cart.

• 

Do not

 use on inclines; cart may tip or roll away.

• 

Do not

 overload the cart! Maximum load rating

 

 

 

Cart #110486: 1,750 lbs. 

 

 

Cart #110488: 2,000 lbs.

•  Inflate tires with ambient air only. 

Never

 use a 

flammable gas to inflate the tires

.

•  Inflate tires to the proper level as indicated on the 

tires. 

• 

Never

 allow riders on the cart.

•  Exercise caution when loading and unloading the 

cart. Place all loads evenly on the cart bed. Center 

loads on the bed to prevent tipping. 

DO NOT STACK 

HEAVY LOADS ON THE END OR SIDES OF THE 

BED!

CARE AND MAINTENANCE

•  Periodically check nuts and bolts to verify they are 

tight and secure.

•  Clean the

 

cart using water and mild soap. Rinse with 

water sprayed from a garden hose.

•  Inspect all cotter pins (if equipped) and verify they 

are in position, secure, and in good condition.

•  Check tire pressure and adjust to recommended 

pressure if needed. 

REQUIRED TOOLS

The following list identifies the main tools needed for 

assembly. 

For easier assembly, an assistant is needed

.

•  Flathead screwdriver
•  Metric and standard wrenches
•  Ratchet and socket set (standard and metric)
•  Pliers
•  Drill and 3/8" drill bit (may not be needed)

UNPACK AND IDENTIFY PARTS

The following steps will ensure that you have all the  

necessary parts before you begin.
1.  Unpack the contents of the shipment and place 

where you can easily inventory the parts. 

Compare 

the shipped parts with those shown at the bottom of 

each page of these instructions.

2.  If anything is missing or you have questions, contact 

customer service.

Summary of Contents for 110486








Reviews: