background image

En 

 FARO Laser Scanner Photon – User’s Manual           

 

38 / 87

 

7

 

Color Option 

With the color option, you can take scans in which each scan point has not 
only its 3D information, but also color value associated with it. 
 

 

Fig.38 Scans with color 

This is done by combining the ordinary scanner with a digital camera. The 
digital camera is hooked onto the scanner and controlled by the scanner 
software. When a color scan is taken, the scanner first performs a normal 
scan and determines a balanced exposure setting. Finally in another turn the 
digital pictures are taken. 

7.1

 

Initial Setup of the camera 

Before you can use the digital camera, you have to ready the camera. 
Depending on the camera you own, have a look at the Nikon D200 or Nikon 
D300 quick start guide and perform the following steps: 
 

 

Charge the battery. 

 

Insert the battery. 

 

Choose a language and set the clock. 

 

Attach the lens (AF Fisheye Nikkor 10.5mm 1:2.8G lens). 

 

Insert the memory card. 

 

Format the memory card. 

 
Be sure to do this at least 2 hours before you want to use the camera, as 
charging an exhausted battery takes some time. 

7.2

 

Setup before scanning 

The first time you want to use the camera for scanning, you have to change 
certain settings of the camera. It is recommended to check these settings 
each time before you use the camera again. 
 

Summary of Contents for Photon 20
























































































Reviews: