background image

Fasep 2000 srl

Rev. 1.8

Balatron 222/212: User’s Manual

23 January 2020

ii

WARNING

.This document contains information which is the property of FASEP 2000 srl and all rights are reserved. This manual shall not be
photocopied or reproduced in any way without the prior written consent of FASEP 2000 srl.

.FASEP 2000 srl reserves the right to revise products firmware, software or documentation without obligation to notify any person
or organization. The information contained in this document is subject to change without warning.

.Prior of the installation of the unit described in this manual, user should read this manual carefully to be instructed properly on
installation, use and maintenance of the unit.

.

Failing to read this manual and operate accordingly may cause damage to the user or the unit

.

.FASEP 2000 srl shall not be responsible for inconvenience, breakdown, accidents due to uncomplete knowledge of this manual
or uncomplete application of recommendations described in this manual.

.FASP 2000 srl shall not be responsible for inconvenience, breakdown, accidents due to unauthorized modifications of the unit, use
of non-original or unauthorized accessories (see Accessories listing in this manual for a list of original accessories available for this
model).

.

FASEP 2000 srl shall not be responsible for any inconvenience, breakdown, accidents caused directly or indirectly by not

qualified service. Service to any parts by not qualified persons will void warranty and will void any right of the owner of
the unit.

SYMBOLS AND CONVENTIONS

To speed the retrieval of main information and make easy to understand the instructions, this manual uses the following typing
conventions:

<NAME OF THE PUSH BUTTON>

Used to indicate name of push-buttons on the control panel.

DISPLAY

Used to indicate text or number visible on the displays on the control panel.

ADVICES

Contain useful advices or solutions,  evidence d with respect to the rest of the text.

NOTE

Notes contain important information, evidenced to the rest of the text.

WARNING

Warning messages appears corresponding to procedures that, if not properly observed,

may lead to loose of data or cause damage to the unit.

!

CAUTION

Caution messages appears corresponding to procedures that, if not properly observed,
may cause injuries to the user.

Summary of Contents for B222























Reviews: