background image

Fasep 2000 srl

Rev. 1.6

Videotronic V548.G4: User’s Manual

15 April 2019

4

1

PRESENTATION

1.0

Intended Use

This unit is designed to measure and correct static and dynamic unbalance of vehicle wheel, the dimension and weight
of which are within the working range of the machine (see “Technical Data”appendix for reference)
This unit is meant for a professional use. Operator shall be properly trained before use. Training Course is not  included
in the price of the unit and must be purchased separately.
This unit is designed for indoor use only (see “Environmental Data”appendix for reference).

!

CAUTION:

This unit is designed to spin vehicle wheels only, within the range of dimensions and weight
approved (see “Technical Data”appendix for reference). Special adaptors suit this purpose. Do not
attempt to use the machine to spin anything else. Unproper locking may cause the part being
spinned to be ejected, causing damage to the unit itself, the operator or anything in the in the
neighboorhood.

1.1

Definitions

1. Monitor
2. Weights and tools trays
3. Side flange-holders 
4. Foot pedal

5. Wheel guard
6. Quick lock + HD shaft
7. ALU-S

Summary of Contents for VIDEOTRONIC V548.G4




















Reviews: