User Manual
(Rack Sold Separately)
Table of Contents
Need Help? ....................................................................................Page 1
Parts List ........................................................................................Page 2
Precautions ...................................................................................Page 3
Pump Orientation .........................................................................Page 4
Assembly Instructions..................................................................Page 5
Screw Diagram for FastWasher12...............................................Page 6
Screw Diagram for FastWasher24...............................................Page 7
FastWasher Tips ............................................................................Page 8
Top Frequently Asked Questions (FAQs).....................................Page 9 - 10
Limitation of Liability ..................................................................Page 10
Contact Information ....................................................................Page 11
NEED HELP?
Step 1: Check out our website - Go to www.FastBrewing.com
Step 2: Read FastWasher FAQ - Click on “FAQs” -> “FastWasher FAQs”
( http://www.fastbrewing.com/content/fastwasher-faqs)
Step 3: If you can’t find what you’re looking for,
send an email to Info@FastBrewing.com or
call us at 1 800 549 5763. Email is best as we require
a paper trail for replacement parts and inquires.
1
*No gasket is needed for the FastWasher24.
We improved the design and no longer require a gasket.
FastWasher12
1 - 530 Gallon Per Hour UL 3-Prong Grounded Pump
1 - Top HDPE Plastic Manifold
1 - Bottom HDPE Plastic Manifold
25 - Screws
25 - Nuts
1 - CO2 Cap Cover
4 - HDPE Plastic Legs
1 - Set of Instructions
FastWasher24
2 - 530 Gallon Per Hour UL 3-Prong Grounded Pumps
1 - Top HDPE Plastic Manifold
1 - Bottom HDPE Plastic Manifold
37 - Screws
37 - Nuts
2 - CO2 Cap Covers
4 - HDPE Plastic Legs
1 - Set of Instructions
Parts List
2
*No gasket is needed for the FastWasher12.
We improved the design and no longer require a gasket.
Electric Shock -
FastWashers
must always be used in a GFCI (Ground-fault circuit interrupter) plug.
They can NEVER be used in a regular household plug. If you don’t know if you are using a GFCI outlet
consult with a licensed electrician.
Dry Running Pump
- The pump CANNOT ever be run without being fully submerged in water.
The pump is not self-priming so the sink or tub you are using must always be full of water so that
the water is level with the main body of the FastWasher. If the pump is ever run without
water it voids the warranty.
FastRack with Bottles
- Always make sure you have a
FastRack
that is full of bottles on the
FastWasher before plugging it in. There is NO
On/Off
switch so water will immediately starting
flowing out of the nozzles once the pump is plugged in.
Do Not Overtighten the Pump(s)
- The pumps are only meant to screw on until you feel them
snug against the
FastWasher
. Do not screw them on any further. This is all that is needed to
create a seal. Never leave the
FastWasher
unattended while it is running. See page 4 for where cords
should be placed (Pump Orientation).
Water Temperature -
Never use water warmer than 106 Fahrenheit or 41 Celsius. The pump is
cooled by the water so water any hotter than above will cause the pump to burn out. Using water
above 106 Fahrenheit or 41 Celsius voids the warranty.
Electric Drills
- DO NOT USE an electric drill on the screws. This will void the warranty as
electric drills can easily overtighten the stainless steel screws and damage the plastic body
of the
FastWashers
.
Always use a FastRack
- The warranty is void if a
FastRack
is NOT used when rinsing, cleaning or
sanitizing bottles. The
FastWasher
nozzles are not meant to support bottles and can break off
when bottles are placed over them.
Pump Rinsing
- Always fully rinse the pump in clean water after use to flush out any debris and
chemicals. Pull off the front casing that has the filter in it and run water through the top threaded
inlet to flush the pump out.
Precautions - Read Before Use
3
