background image

 

Thank you for your purchase of your Xtreme Fat Tire Bike.   

INITIAL INSPECTION: 

Please inspect your packaging upon arrival for any damage that may have occurred in shipping. 
If you see any damage take photographs, and call us immediately so we can file a claim if 
necessary. Please do not remove the bike until we file a claim with FedEx. 

RETURNS: 

Please note:

 As per our policy on the website, returns must be made within 3 days of delivery 

and are subject to a 20% restocking fee. You must call us at 757-635-5160 if you intend to return 
the bike so we can issue a RMA (Return Material Authorization) number. Returns will not be 
accepted any other way. After the 3-day period, all sales are final. Return shipping costs are the 
responsibility of the buyer, unless the bike is damaged in shipping. 

CHARGE-BACKS: 

We will do everything in our power to honor the 1-year warranty on parts and ensure your 
satisfaction with our products. If you have a defective part, you must return it to us before we can 
send you a replacement part. A chargeback to your credit card company is not a method of 
correcting a warranty issue as you already have your electric bike. We consider charge-backs as 
a form of theft when you already have your merchandise and will prosecute them to the full 
extent of the law and you will be responsible for all attorneys’ fees. 

LEGAL ACTION: 

Fatty AT E-Bikes is a limited liability corporation located in Deerfield Beach, FL. Any legal 
action taken against the company, or its employees or owners must be in the jurisdiction of 
Broward County, Florida.  

 

 

 

Summary of Contents for E-Bike

















Reviews: