background image

inches away from your mouth. While holding the PTT button, speak into

the microphone in a normal tone of voice.

Release the PTT button when you have finished transmitting.

For others to receive your transmission, they must be on the same

channel with you.

Note:

1, The transmitting range will depend on your surroundings and

environment. It will be affected by obstructions such as hills or buildings.

2, Don’t try to use two devices which are less than 1.5m (5 feet) apart.

Otherwise, you may experience interference.

4.5 Changing Channels

Press the MENU button once; the channel number will flash on display.

Press the up

/down

button to switch channels.

Press the PTT button to confirm and return to standby mode.

Note:

If no button is pressed within 15 seconds during setting, the

device will return to standby mode.

4.6 CTCSS (Continues Tone Coded Squelch System)

Press the MENU button twice; the current CTCSS code will flash on the

screen. Press the up

/down

button to select from the 38 available

codes.

Press the PTT button to confirm and return to standby mode.

License free radio is operating on the 400-470MHZ frequency band, the

device has 8/22(optional) available radio channels. If there are many

users nearby, there is a chance that some of the users are operating on

the same channel.

When using CTCSS, a low-frequency tone (between 67-250Hz) will be

transmitted along with the voice signal. There are 38 tones available. You

are free to choose from the 38 available sub-channels. Due to filtering,

these sub-channels will generally not be audible, so there will be no

interruption in the communication.

4.7 VOX (Hands-free function)

Press the MENU button three times, the current VOX setting will flash on

the screen, and the VOX icon will be displayed.

Press UP

button to set the VOX sensitivity level from 1 to 3 (level 3 is

the most sensitive level).

Press down

button until “OFF” appears on the screen to turn VOX

function OFF.

Press the PTT button to confirm and return to standby mode.

In VOX mode, the radio will transmit a signal when it is activated by your

voice or other sound around you.

VOX Operation is not recommended if you plan to use your device in a

Summary of Contents for TWIN SET









Reviews: