background image

 
 

© Interleader Limited 2017 

19 of 30 

Printed: 06/09/2017 

18  UHF Radio Modem Specification 

The same Telit UHF Radio Modem is used in MIL-Star, HEMS-Star, RLC, MLC, PLC and KFC and the 
FEC Systems Management PC Dongle. The Modem has the following specification. 

Parameter 

Value 

UK/EU/ROW 868 MHz 

USA 915MHz 

Manufacturer: 

Telit 

Telit 

Modem type: 

LE70 - 868  

LE70 - 915  

Nominal frequency band: 

868MHz 

915MHz 

Frequency (sub)band: 

869.525MHz (869.4 - 869.65MHz) 

902 

– 928MHz (915.375 1

st

 Channel) 

Frequency hops/dwell time: 

N/A 

50/350mS 

Freq. tolerance @ 20C 

+/-2.5kHz 

+/-2.5kHz 

Rx filterb 

81kHz 

81kHz 

Deviation: 

+/-20kHz 

+/-20kHz 

Power output set 

100mW (20dBm) 

100mW (20dBm) 

Receiver sensitivity: 

Max 

–110dBm  at 38.4kbps 

Max 

–110.5dBm  at 38.4kbps 

Controller range: 

To 200m subject to antenna & terrain  

To 200m subject to antenna & terrain 

Addressing - module level: 

Transparent (secure addressing later) 

Transparent (secure addressing later) 

Addressing schema: 

One to Many 

One to Many 

Addressing 

– device level: 

Handled in software 

Handled in software 

Encryption: 

None (AES 128bit later) 

None (AES 128bit later) 

RF Baud rate:  

38.4kbps 

38.4kbps 

Modem data rate: 

19.2kbps 

19.2kbps 

Modulation: 

2GFSK 

2GFSK 

Operating temperature: 

-40C to +85C 

-40C to +85C 

 

 

 

Compliance: 

CE (0682) 

Compliance  for  FCC  is  to  47  CFR  part 
15.249. FCC ID: R17LE70FH 

RF Channel Selection 

The EU standard sets maximum power transmission limits dependent on frequency, bandwidth 
and application. A rough guidance applicable to the ZULU channel numbers is given below  

Channel Number 

Frequency Centre (MHz) 

EU Power Allowance 

mW/dBm 

Notes 

868.400 

25/14 

Applicable standard - 

EN300-220 

868.900 

25/14 

869.450 

100/20 

869.600 

100/20 

869.800 

25/14 

All specifications are manufacturer

’s data

 

Summary of Contents for HP0722































Reviews: