background image

H

igH

L

igHter

™ LED Mini-Lightbars

15

Table 2  Flash patterns for standard 12 V 

H

igH

L

igHter

 models

Pattern 

Number Description

Amber

SAE J845 

Class***

1

Alternating Quad Flash

2

Full Quad Flash – 80 Quad Flashes per Minute

1

3

Continuous Flash – 75 ms On, 75 ms Off

4

Alternate Double Flash – 75 Double Flashes per minute – Sides Alter-

nate with Front and Back

5

Rotate With 2 Heads On – 75 ms Between Flashes

2

6

Rotate With 2 Heads On – 50 ms Between Flashes

2

7

Alternate Triple Flash – 90 Alternating Triple Flashes per minute

8

Alternating Sides Quad Flash – 60 Alternating Quad Flashes per 

minute

9

Continuous Flash – 125 ms On, 125 ms Off – 240 FPM

10

NFPA Flash – 400 ms On, 400 ms Off – 75 FPM

1

11

Continuous Flash – 250 ms On, 250 ms Off – 120 FPM

1

12

Rotate Left Followed by Full Quad – 67 Full FPM

13

Double Flash Followed by Alternating Side Quad Flash – 40 FPM

14

Rotate Heads Inside Out – 340 FPM

15

Rotate Heads Inside Out and Back In – 120 FPM

16

Scroll Heads From End to End – 75 FPM

17

Rotate Heads Once Followed by Scroll Left to Right – 85 FPM

18

FedPulse 150 – 150 Pulsed Flashes

2

19

FedPulse 75 – 75 Pulsed Flashes

1

20

Steady – Test Marking Pattern

21

N/A

Summary of Contents for HighLighter





















Reviews: