Feeney DesignRail LED 40W-DK Installation Instructions Manual Download | Manualshive

Page: 1 / 11

background image

1-800-888-2418 | www.feeneyinc.com

1

Rev: 10/21

Drivers are available in a variety of wa ages. In general a driver should not exceed more than 80% of its rated wa age. (Example:
60W Driver = 60 x 0.8 = 48W Max).

Building codes vary by loca on and jurisdic on. Consult all applicable codes before installing DesignRail® LED Ligh ng. DesignRail

®

LED Ligh ng may not be suitable for every applica on and it is the sole responsibility of the installer to ensure that DesignRail

®

LED

Ligh ng is used for its intended purpose.

WARNING: ELECTRIC SHOCK IS ALWAYS POSSIBLE WHEN WORKING WITH ELECTRICITY. THIS CAN CAUSE SERIOUS PERSONAL
INJURIES OR DEATH. ELECTRICAL SHORTS CAN ALSO CAUSE FIRES AND PROPERTY DAMAGE. ALWAYS MAKE SURE THE

ELECTRICAL OUTLET YOU ARE PLUGGING INTO IS GROUNDED.

DesignRail

®

24V LED Post Accent Light

Installa on Instruc ons

1
2
3
...
»

Summary of Contents for DesignRail LED 40W-DK












Reviews:

No comments

Related manuals for DesignRail LED 40W-DK

Brand: Yardistry Pages: 4

Brand: VARSITY Scoreboards Pages: 11

Brand: Poly-Wood Pages: 2

Brand: JOBE Pages: 2

Brand: Z-SHADE Pages: 2

Brand: Hudora Pages: 8

Brand: LuxenHome Pages: 5

LAVDN7PCSW-BLU-SU

Brand: Hanover Pages: 14

Brand: Superior Fireplaces Pages: 30

Brand: BCP Pages: 16

Inversee 118B50033

Brand: Gama Sonic Pages: 4

Galaxy Street Eco

Brand: IPAS Pages: 3

Brand: Porter Pages: 2

Brand: Alpine Pages: 2

Brand: Backyard Creations Pages: 6

Brand: RaceAmerica Pages: 9

Levanto Lounger

Brand: J D Williams Pages: 6

UFO StrobeClamp

Brand: Hagerman Audio Labs Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands