background image

Table of Contents

Included accessories...............................................................................................................................................................................2
Table of Contents....................................................................................................................................................................................3
Chapter 1 Safety and specification introduction.................................................................................................................................4
Chapter 2 Assembly instructions..........................................................................................................................................................8
Chapter 3 Product specification...........................................................................................................................................................13
Chapter 4 Instructions for use..............................................................................................................................................................14
Chapter 5 Lubrication instructions......................................................................................................................................................21
Chapter 6 Engine description...............................................................................................................................................................21
Chapter 7 Machine cleaning and storage............................................................................................................................................21
Chapter 8 Machine maintenance instructions....................................................................................................................................22
Chapter 9 Maintenance planning cycle...............................................................................................................................................23
Chapter 10 Troubleshooting and solutions.........................................................................................................................................24
Chapter 11 Environmental protection.................................................................................................................................................25
Chapter 12 Declaration of conformity.................................................................................................................................................26
Chapter 13 WARRANTY......................................................................................................................................................................27
Chapter 14 PRODUCT FAILURE.......................................................................................................................................................28
Chapter 15 WARRANTY EXCLUSIONS...........................................................................................................................................29

03

Summary of Contents for FAST175P-1






























Reviews: