background image

That the machine shall always be used in accordance with these
manufacturer's instructions the instruction handbook

The engine shall be stopped when carrying out maintenance and
cleaning operations, when changing tools and when being transported
by means other than under its own power;

Some hazards can be met when working on slopes; work slowly by
holding firmly the tool. Do not transport the tool on slopes. The hazards
can rise when working on difficult soil (stony, hard, etc.). there is a risk
to hit some objects, sliding, lose control for the machine which will gives
damages. Always inspect the working area before working, and always
watch what you are doing.

The adjustable part of the protective device shall be adjusted to the
working depth of the tool so that only that part of the working tool that
cuts into the soil remains uncovered. This does not apply to motor hoes.

The machine should only be operated by suitably trained persons.

During the operation of the machine safety shoes should be worn.

Always start up the machine under normal conditions.

Intended use
This device is to be used only as an electric hoe for aerating lawns and
grassy areas in private home gardens and pleasure gardens. It is not
intended for use in public spaces, parks, sports fields, agriculture or forestry.
Use of this device for any other purpose is considered incorrect and
unapproved. The manufacturer will not be responsible for any damage or
injury resulting from such use. The user is fully responsible for all related
risks.

Summary of Contents for FMTB50
























Reviews: