background image

5. REPLACEMENT OF PARTS AND MAINTENANCE   

1)

 

REPLACEMENT PARTS /ACCESSORIES 

WARNING!  Only  use  accessories  specified  in  the  operating  manual.  Using  the  accessories  other 

than those specific in the operating manual may cause a risk of injury. Only get the accessories from the 
Service Centre. 

2)

 

MAINTENANCE 

WARNING! RISK OF INJURY!   

 

Pull the mains plug before any adjustments, maintenance or repair. 

 

Repair and servicing work not described in this manual should always be carried by the Service Centre. 
Use only the original parts. 

 

The  following  cleaning  and  servicing  should  be  done  regularly.  This  will  ensure  a  long  and  reliable 
service life. 

 

Do not spray the appliance with water and do not immerse it in water. 

Electric Shock

 hazard. 

 

Keep clean the ventilation slots, motor housing and handles of the appliance. Use a damp cloth or a 
brush. Do not use cleaning agents or solvents. You may otherwise irreparable damage the appliance. 

3)

 

STORAGE 

 

Switch off and unplug the appliance before storage. 

 

Allow the sander to cool down. 

 

Store the appliance in a dry and secure place well out of reach of children. 

 

Empty the dust collection box before storing the appliance.   

4)

 

TRANSPORT 

Before transporting, observe the followings: 

 

Switch off and unplug the appliance. 

 

Allow the product to cool down. 

 

Put the appliance and accessories into the case. 
 

6. DISPOSAL                                                                                                         

To help the environment, please dispose of the product properly when it has reached the end of 
its useful life and not in the household waste. Information on collection points and their opening 

hours can be obtained from your local authority 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for FPO350















Reviews: