15
en
Do not rivet or screw any name-plates or signs onto the
power tool.
If the insulation is damaged, protection against
an electric shock will be ineffective. Adhesive labels are
recommended.
Before putting into operation, check the mains connection
and the mains plug for damage.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
Handling hazardous dusts
For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to
one’s health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles
from materials containing stone, paint solvents, wood
preservatives, and antifouling paints for vessels, can trig-
ger allergic reactions to the operator or bystanders and/
or lead to respiratory infections, cancer, birth defects or
other reproductive harm. The risk from inhaling dusts
depends on the exposition. Use dust extraction matched
appropriately for the developing dust, as well as personal
protective equipment and provide for good ventilation of
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of sanding dust
and chemical materials can self-ignite under unfavourable
conditions or cause an explosion. Avoid sparking in the
direction of the dust collector as well as overheating of
the power tool and the materials being sanded, empty
the dust collector/container in time, observe the material
manufacturer’s working instructions, as well as the rele-
vant regulations in your country for the materials being
worked.
At a glance.
The following numbering of the product fea-
tures refers to the illustrations at the beginning
of this Instruction Manual. (See the respective
Figure on pages 3 and 4)
1 Wheel guard with tightening screw (1a)
For loosening/tightening the guard.
2 Threaded flange
Attaching or changing the grinding disc.
3 Threaded flange with outer flange
Attaching or changing the grinding disc.
4 Switch
For switching the power tool ON and OFF,
ON/OFF switch (4b),
Lock-off (4c).
5 Standard accessories
Face spanner (5d),
Locking pin (5e),
Allen key (5f),
Threaded and inner flange (5g),
Threaded flange, inner and outer flange (5h),
Centring sleeve (5i).
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
instruction manual.
Instructions for putting into operation.
Connection to the power supply.
The power tool is supplied from the factory with a con-
nection cable without a plug.
Recommendation: For protection against overstressing,
the power tool is fitted with an appropriate FEIN motor
protection plug.
The plug should be mounted by an electrical expert.
Before putting into operation, check the direction
of rotation of the drive shaft without any mounted
wheels and have it corrected if it does not agree.
The direction of rotation is marked on the power
tool with an arrow.
The output voltage and the power supply fre-
quency must agree with the specifications on the
name plate of the power tool.
If FEIN frequency converters are used, reliable operation
of the power tool is guaranteed.
Follow the steps in the operating instructions of
the frequency converter.
Operating instructions.
Adjustments.
Adjusting the guard (Figure 1).
➤
Loosen the tightening screw (1a).
➤
Swivel the guard (1) into the required working
position.
➤
Tighten the tightening screw (1a) firmly.
Changing the tool.
Attaching or changing the wheel (Figures 2 + 3).
➤
MSho852-1/MShyo852-3a/4a:
Lock the drive
spindle at the inner flange with the locking pin (5e).
➤
MShyo869-1:
Lock the drive spindle with the
Allen key (5f).
➤
Loosen the threaded flange (2) with the face
spanner (5d).
➤
Completely unscrew the threaded flange (2).
3 41 01 073 06 0.book Seite 15 Donnerstag, 5. November 2015 11:08 11
