33
en
For your safety.
Read all safety warnings and all
instructions.
Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have
thoroughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 465 06 0). The documents mentioned should
be kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the power tool:
Magnetic core drill unit for drilling with core drill bits
and solid drill bits, reaming, countersinking and tapping
on materials with surfaces suitable for magnets in
weather-protected environments using the application
tools and accessories recommended by FEIN.
In environments subject to interference, a reduction of
the operating quality is possible; this can include tem-
porary failure, temporary reduction of the function or
the intended operating behaviour, for the correction of
which intervention by the operator is required.
This power tool is also suitable for use with AC gener-
ators with sufficient power output that correspond to
the Standard ISO 8528, design type G2. This Standard
is particularly not complied with when the so-called dis-
tortion factor exceeds 10 %. When in doubt, please
refer to the generator instruction/specification guide.
Character
Unit of measure-
ment, international
Unit of measure-
ment, national
Explanation
P
1
W
W
Power input
P
2
W
W
Output
n
0R
/min, min
-1
, rpm,
r/min
rpm
No-load speed (clockwise)
in
inch
inch
Size
U
V
V
Rated voltage
f
Hz
Hz
Frequency
M...
mm
mm
Size of metric thread
Ø
mm
mm
Diameter of a round part
HM
mm
mm
Max. capacity in steel with up to 400 N/mm
2
– TCT (core drill bit)
HSS
mm
mm
Max. capacity in steel with up to 400 N/mm
2
– high speed steel (core drill bit)
HSS
mm
mm
Max. capacity in steel with up to 400 N/mm
2
– high speed steel (twist drill bit)
mm
mm
Max. drill chuck capacity
mm
mm
Reamer diameter
mm
mm
Counterboring diameter
mm
mm
Tap
MK / MT / CM
Morse taper size
(ISO 296)
MT
Morse taper size (ISO 296)
kg
kg
Weight according to EPTA-Procedure 01
T
a
°C
°C
Allowable ambient temperature
L
pA
dB
dB
Sound pressure level
L
wA
dB
dB
Sound power level
L
pCpeak
dB
dB
Peak sound pressure level
K...
Uncertainty
m/s
2
m/s
2
Vibrational emission value according to
EN 62841 (vector sum of three directions)
h
m/s
2
m/s
2
Mean vibrational value for core drilling
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
Basic and derived units of measurement
from the international system of units
SI
.
Fe 400
Fe 400
Fe 400
WARNING
Summary of Contents for 72706061000
