Fein AGSZ18-280BL Original Instructions Manual Download

Page: 23 / 126

Beware of any concealed electric cables, gas or water
conduits.

Check the working area before commencing

work, e. g. with a metal detector.

Do not rivet or screw any name-plates or signs onto the
power tool.

If the insulation is damaged, protection

against an electric shock will be ineffective. Adhesive
labels are recommended.

Never look or stare into the light of the power tool’s
lamp from a short distance. Never point the light of the
lamp into the eyes of other persons in close vicinity.

The radiation produced by the lamp can be harmful for
the eye.

Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

Do not position your body in the area where power tool
will move if kickback occurs.

Kickback will propel the

tool in direction opposite to the wheel’s movement at
the point of snagging.

After working gypsum-containing materials: Blow out
the ventilation openings of the power tool and the
switch element with dry and oil-free compressed air.

Otherwise, gypsum-containing dust can settle in the
power tool housing and switch element, which can
harden in connection with humidity. This can impair the
switching mechanism.

Use and handling of the battery (battery pack).

To avoid hazardous situations such as burns, fire,
explosion, skin injuries, and other injuries when han-
dling the battery, observe the following instructions:

Batteries must not be disassembled, opened or reduced
in size. Do not subject batteries to mechanical impact
or shock.

Hazardous vapours and fluid can escape in

case of damage and improper use of the battery. The
vapours can irritate the respiratory system. Liquid
ejected from the battery may cause skin irritations or
burns.

When battery fluid from a damaged battery has come
into contact with objects close by, check the respective
components, clean them or replace them as required.

Keep the battery away from heat and fire. Do not store
the battery in direct sunlight.

Do not remove the battery from its original packaging
until it is going to be used.

Before any work on the machine itself, remove the bat-
tery from the power tool.

If the power tool accidentally

starts, there is danger of injury.

Remove the battery only when the power tool is
switched off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture
and water.

Clean contaminated battery terminals and

power tool connections with a dry, clean cloth.

Charge the batteries only with battery chargers recom-
mended by the manufacturer.

A charger that is suitable

one type of battery pack may create a risk of fire when
used with another battery pack.

Keep the battery not being used away from paper clips,
coins, keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.

Shorting the battery terminals together may

cause burns or a fire.

Remove the power tool's battery during transport and
storage.

Use only intact original FEIN batteries that are intended
for your power tool.

When working with and charging

incorrect, damaged, repaired or reconditioned batter-
ies, imitations or other brands, there is danger of fire
and/or explosion.

Follow the safety warnings in the operating instructions
of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information
sheet has been measured in accordance with a stand-
ardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However, if the tool is
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may
differ. This may significantly increase the exposure level
over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the oper-
ator from the effects of vibration such as: maintain the
tool and the accessories, keep the hands warm, organi-
sation of work patterns.
The vibrational emission values are given for dry grind-
ing of metal with grinding points. Other applications,
such as shaping with hard metal cutters, can lead to
other vibrational emission values.

Handling hazardous dusts

For work procedures with this power tool where
material is removed, dusts develop that can be hazard-
ous to one’s health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate parti-
cles from materials containing stone, paint solvents,
wood preservatives, antifouling paints for vessels, can
trigger allergic reactions to the operator or bystanders
and/or lead to respiratory infections, cancer, birth
defects or other reproductive harm. The risk from
inhaling dusts depends on the exposition. Use dust
extraction matched appropriately for the developing
dust, as well as personal protective equipment and pro-
vide for good ventilation of the workplace. Leave the
processing of asbestos-containing materials to special-
ists.
Wood and light-metal dust, hot mixtures of grinding
dust and chemical materials can self-ignite under unfa-
vourable conditions or cause an explosion. Avoid
sparking in the direction of the dust collector as well as