Fein ASW 10-10 Manual Download

Page: 13 / 124

For your safety.

Read all safety warnings and all
instructions.

Failure to follow the

warnings and instructions may result in electric shock,
fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed “General

Safety Instructions” (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.

Intended use of the power tool:

Hand-held screwdriver for screwing in and unscrewing
screws and nuts in weather-protected environments
without water supply using the application tools and
accessories recommended by FEIN.

Special safety instructions.

Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring.

Fasteners contacting a “live” wire may

make exposed metal parts of the power tool “live” and
could give the operator an electric shock.

Beware of any concealed electric cables, gas or water
conduits.

Check the working area before commencing

work, e.g. with a metal detector.

Secure the work piece firmly.

A work piece that is

gripped tightly in a clamping device or vice, is more
secure than if held by hand.

Hold the power tool firmly.

High reaction torque can

briefly occur.

Do not machine any material containing asbestos.

Asbes-

tos is cancerogenic.

Do not rivet or screw any name-plates or signs onto the
power tool.

If the insulation is damaged, protection

against an electric shock will be ineffective. Adhesive
labels are recommended.

Do not use accessories which are not specifically
designed and recommended by the power tool manufac-
turer.

Safe operation is not ensured merely because an

accessory fits your power tool.

Never look or stare into the light of the power tool's lamp
from a short distance. Never point the light of the lamp
into the eyes of other persons in close vicinity.

The radi-

ation produced by the lamp is harmful for the eye.

Use and handling of the battery (battery pack)

To avoid hazardous situations such as burns, fire, explo-
sion, skin injuries, and other injuries when handling the
battery, observe the following instructions:

Batteries must not be disassembled, opened or reduced
in size. Do not subject batteries to mechanical impact or
shock.

Hazardous vapours and fluid can escape in case of

damage and improper use of the battery. The vapours can
irritate the respiratory system. Liquid ejected from the
battery may cause skin irritations or burns.

When battery fluid from a damaged battery has come into
contact with objects close by, check the respective com-
ponents, clean them or replace them as required.

Keep the battery away from heat and fire. Do not store the
battery in direct sunlight.

Do not remove the battery from its original packaging
until it is going to be used.

Before any work on the machine itself, remove the bat-
tery from the power tool.

If the power tool accidentally

starts, there is danger of injury.

Remove the battery only when the power tool is switched
off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture
and water.

Clean contaminated battery terminals and

power tool connections with a dry, clean cloth.

Use only intact original FEIN batteries that are intended
for your power tool.

When working with and charging

incorrect, damaged, repaired or reconditioned batteries,
imitations or other brands, there is danger of fire and/or
explosion.

Follow the safety warnings in the operating instructions
of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However, if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.

Operating Instructions.

The power tool is equipped with a soft-starting feature.
If the motor switches off after a proper screwdriving
operation, restarting is not possible until after 0.8 sec-
onds. This prevents accidental retightening of already
tightened screws.

Handling the battery.

Operate and charge the battery only within the battery
operating-temperature range of 0°C – 45°C (32°F –

113°F). At the beginning of the charging procedure, the

battery temperature must be within the battery operat-
ing-temperature range.

WARNING

OBJ_BUCH-0000000059-001.book Page 13 Monday, January 16, 2012 3:14 PM