23
en
direction of the dust collector as well as overheating of
the power tool and the materials being sanded, empty the
dust collector/container in time, observe the material
manufacturer’s working instructions, as well as the rele-
vant regulations in your country for the materials being
worked.
Operating Instructions.
The
self-start lock
prevents the angle grinder (see Table)
from automatically restarting again, even after a brief
interruption of the power supply, e. g., from a pulled
mains plug.
Angle grinders with electronics (see Table) are equipped
with overload and blocking protection. In case of over-
load or blocking of the application tool, the power supply
is interrupted. In this case, switch the power tool off,
remove it from the work piece and check the application
tool. Afterwards, switch the power tool on again.
Press the locking button only when the motor is
stopped (see page 5).
Turning the machine head:
Carefully turn the machine head to the new position (see
page 7)
without removing it from the housing
.
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.
The total insulation of the power tool can be impaired.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air,
and connect a residual current device (RCD) on the line
side.
If the supply cord of this power tool is damaged, it must
be replaced by a specially prepared cord available through
the FEIN customer service centre.
The current spare parts list for this power tool can be
found in the Internet at www.fein.com.
If required, you can change the following parts yourself:
application tools, auxiliary handle, clamping flanges,
wheel guard
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer’s warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. FEIN GmbH, C-DB_IA,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
Selection of accessories (see page 12).
Use only original FEIN accessories. The accessories must
be intended for the power tool type.
A
Grinding disc, flap disc
(use only with mounted wheel guard)
B
Cutting disc
(use only with mounted cut-off wheel guard)
C
Steel wire brush, fleece backing pad
(use only with mounted wheel guard)
D
Backing pad for fibre sanding sheets, fibre sanding
sheets
(mount only with the provided backing-pad clamping
unit; use only with mounted hand guard or wheel
guard)
E
Steel tapered twist brush
(use only with mounted wheel guard)
F
Backing pad with Velcro, Velcro sanding sheets,
sanding fleece with Velcro attachment, sponges
(use only with mounted hand guard)
G
Steel cup brush, round twist brushes
(use only with mounted hand guard)
WSG12-125P
WSG15-125PSQ
WSG12-125PQ
WSG15-150P
WSG15-125P
WSG15-150PQ
WSG15-125PQ
WSG15-70Inox
WSG15-125PS
OBJ_BUCH-0000000123-002.book Page 23 Tuesday, August 13, 2013 9:40 AM
Summary of Contents for WSG8-115
