These sanders are provided with a dust aspiration
output which adapts to a universal vacuum or any other
dust aspiration device.
CAUTION:
Always use an aspiration extractor designed
according to the guidelines applicable to dust emission.
The flexible hoses of conventional vacuum cleaners fit
directly onto the dust extraction nozzle.
The aspirator should be suitable for the material being
worked.
A special aspirator must be employed in those cases
where dry harmful or carcinogenic dust is produced.
ACCESSORIES
Accessories and their corresponding order number can
be found in our catalogues.
MAINTENANCE AND CARE
WARNING!
Always unplug the machine before carrying
out work on it.
-
Inspect the tool:
Using a worn out polishing or polish-
ing tool will reduce working efficiency.
-
Inspect the mounting screws:
Regularly inspect all
the mounting screws and ensure they are firmly tight-
ened. Should any screw be loose, tighten it immedi-
ately. Failure to do so could put you at serious risk.
-
Motor maintenance:
Always take the greatest care
over this and make sure that the motor winding is not
damaged and does not become wet with oil or water.
-
The vents should always be kept clean and free of
obstacles.
-
Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
-
Check that the mains lead is in good condition. If
it is not, take it to an Official Service Centre to
have it replaced.
-
Brush replacement:
The brushes should be replaced
after 150 - 200 hours use or when they are less than
10 mm long. Have this done by an Official Service
Centre. We recommend that at every second change
of brushes, you take the machine to one of our Official
Service Centres for general cleaning and oiling.
-
Use only
Felisatti
accessories and spares. Parts the
changing of which is not covered in this instruction
manual, should be replaced in a
Felisatti
Official
Service Centre (See Warranty/Official Service Centre
address leaflet).
Do not dispose of electric tools in
the household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances and
its translation into national law, used electric tools must
be collected separately and recycled in an ecologically
desirable way.
WARRANTY
See general warranty conditions printed on the attached
sheet.
NOISE AND VIBRATION
This tool has been designed and made to reduce noise
to a minimum. However, in spite of this
, in certain
circumstances the maximum noise level in the place
of work could exceed 85 dBA. In this case, the op-
erator should wear ear protection.
The machine's noise and vibration levels, measured in
compliance with EN 60745-1, usually reach:
Acoustic pressure = 90 dB(A)
Sound-power level = 103 dB(A)
Use ear protection!
Vibration acceleration = 2.9 m/s
2
DECLARATION OF CONFORMITY
We hereby declare, under our sole responsibility,
that the
FELISATTI
brand products described in this
manual APF200/1010LE comply with the following
standards or standard documents: EN60745-
1:2008, EN60745-2-3, EN60745-2-4, EN55014-
1:2006+A1, EN55014-2:1997+A1+A2, EN61000-3-
2:2006+A1+A2 and EN61000-3-3:2008 in accor-
dance with EU Directives 2006/42/EC, 2006/95/EC,
2004/108/EC and 2002/95/EC.
11
Francisco
Ruiz
Plant Mgr.
We reserve the right to make technical changes 07/2011
Summary of Contents for APF200/1010LE
