Felisatti NTF250/1200ST, Operating Instructions Manual

6.11 IMPROPER USE

The functions and use of this tool are those exclusively

indicated in this manual. Never use the tool to cut thick

tree trunks or branches. 

Any other use of the tool is explicitly forbidden.

-Never cut aluminium or steel on the upper table.

-Always use sharp blades appropriate to the type 

of cuts to be made. 

-Never  use  the  machine  without  the  protective 

devices described.

-Never  use  the  machine  for  food-processing 

purposes.

-Use only the right types of blade (see Table, Point 

6.1)  for  the  material  to  be  cut:  wood,  aluminium 

sections, PVC pipe, etc.

The  cutting  of  any  other  type  of  material  not 

specified in this manual is expressly prohibited. 

The  machine  comes  with  a  brush  that  conveys 

all  dust  into  the  suction  area  in  order  to  limit  the 

quantity of dust generated during cutting.

WARNING! 

Whenever wood is cut, connection to an 

external vacuum unit must be used in order to lower 

the risk of exposure to dust.

Always wear dust-proof face masks.

7 MAINTENANCE

WARNING

 - Always unplug the plug from the power 

supply socket before performing.

maintenan 

Note:  operating  noise  can  be  decreased  by 

using  the  right  blades  and  performing  frequent 

maintenance on the blade and mitre saw itself.

7.1 LUBRICATION

The mitre saw is delivered already completely 

lubricated and does not require any further lubrication.

7.2 ROUTINE CLEANING

WARNING

 - Avoid touching the handgrip with hands 

that are dirty with oil or grease, and immediately 

clean the handgrip whenever this happens.

 - Clean the machine carefully after use by spraying 

with compressed dry air.

WARNING

 - An attachment that can be easily 

connected to any Felisatti vacuum unit is provide to 

improve work conditions.

7.3 CHECKING THE DRIVE BELT

These machines are equipped with drive belts. 

The right tightness of these belts is essential to 

good operation and must be checked regularly and 

adjusted whenever necessary by proceeding as 

follows:

-  remove  the  casing  over  the  belt  A  (fig.16)  and 

loosen the 4 screws C (fig. 17) that keep the motor 

unit in place.

- adjust the tightness of the belt using the 

corresponding dowel B (fig. 17).

- tighten the 4 screws C (fig. 17) in order to lock the 

motor unit in place and reassemble the protective 

casing ove the belt.

WARNING!

 The failure to perform this operation 

regularly may result in damage to the belt and 

incorrect machine operation.

7.4 DISPOSAL

At the end of the machine working life, or 

when it can no longer be repaired, ensure 

that it is disposed of according to the standard 

regulations of the country in which it is being used, 

and that the disposal operation is carried out by 

specialised personnel following authorised guidelines.

In all circumstances:

- Do not abandon in the environment;

- Do not dispose of together with solid urban

waste products;

- Contact the special recycling centers

8 PART REPLACEMENT

WARNING! - Always unplug the plug from

the power supply socket before replacing

spare parts.

8.1 BLADE REPLACEMENT (fig. 18)

Proceed as follows to replace the blade:

Raise the upper table to its highest permissible height 

- Release the movable protective casing 

L

 (fig. 1) by 

using the button 

B

 and raise it completely - Using the 

two Allen wrenches supplied (on the blade side and 

on the motor side) unscrew the screw 

C

 clockwise - 

Remove the locking flange 

D

, remove the blade by 

first sliding it to the left and then sliding it downwards - 

Mount the new blade after making sure that the teeth 

face the direction indicated by the arrow and then lock 

it in place by screwing the screw 

C

 counter-clockwise 

tightly down - Lower the movable protective casing 

L

by returning button 

B

 to its original position and then 

make sure that the blade is protected when the blade 

unit is completely raised.

WARNING!

 - Use only the blades recommended by 

the Manufacturer and in compliance with Standard 

EN 847-1. Make sure that the speed marked on the 

blade is greater than the tool rated speed.

WARNING!

 - NEVER USE STEEL BLADES FOR 

HIGH SPEEDS.

8.2 REPLACING THE POWER SUPPLY CABLE

Make sure that the power supply cable is in good 

condition; if worn, have it replaced by an authorised 

Assistance center

.