Felisatti NTF250/1200ST, Operating Instructions Manual

INTRODUCTION

Congratulations on your purchase of a new series

FELISATTI

 mitre saw, a high-quality product that will

complete your set of professional tools. This new 

series represents the further evolution of the 

renowned mitre saws developed by 

FELISATTI

. 

If any malfunctions ever occur during operation, 

you will always be able to rely on the network of 

authorised Assistance Centers. All 

FELISATTI

movable tools comply with 

Standard EN 61029

, 

Machine Directive 

98/37/EC

 and amendments, 

with 

2006/95/EC

 and 

93/68/EEC

, and in regard to 

electromagnetic compatibility, with Directive 

89/336/

EEC, EN 55014.1, EN 55014.2, EN61000.3.2

 and 

EN 

61000.3.3

 and 

EN 50366

.

If used with the care and serviced regularly, this tool 

will provide long-lasting and reliable service. Carefully 

follow the instructions contained in this manual, using 

them for reference for any eventual controls that may 

need to be carried out.

1 GENERAL INFORMATION

1.1 THE AIM OF THIS MANUAL

This manual has been prepared by the Manufacturer 

as an integral part of the mitre saw equipment. The 

information contained is for the benefit of professional 

operators. This manual defines the purpose for which 

the mitre saw was designed, and contains all the 

information necessary to ensure safe and correct 

use. We therefore recommend reading the manual 

carefully before proceeding to any form of adjustment, 

operation or maintenance. Constant respect for the 

contents of this manual ensures both machine and 

operator safety and the most economical and longest 

working life of the machine itself. Photographs and 

drawings have been supplied by the manufacturer for

exemplifying purposes; with the aim of following 

a policy of constant development and product 

modernisation, the manufacturer is entitled to make 

modifications without forewarning.

1.2 MITRE SAW IDENTIFICATION

Plate A (fig. 1) provides mitre saw model information 

and technical data of the motor and of its manufacturer; 

Plate B provides mitre saw model identification.

1.2.1 IDENTIFICATION (fig. 1)

A  Data plate

B  Logotype plate

C  Upper table

D  Movable upper casing

E  Handgrip

F  Machine lock pin

G  Lower support stroke-end raised section

H  Turntable

I    Fixed casing

J  Blade

K  Machine lock knob 0°- 45°

L  Turntable lock knob

M  Movable lower blade protector

N  Upper table fine adjustment

O  Release lever

P  Base

Q  Support

R  Main body

S  Upper table locking knob

1.3 MANUFACTURER – IDENTIFICATION

Interskol Power Tools S.L.

Carretera de Sant Joan de les Abadesses s/n17500 

RIPOL, (Girona), SPAIN

Tel +34972700200 - Fax +34972700554E-mail: 

e-mail: felisatti@interskol.es

2 TECHNICAL CHARACTERISTICS

A sturdy, high-reliability structure ensures that these 

mitre saws will be able to cut wooden boards and 

PVC and aluminium pipe in industrial environments 

at no expense to the machine essential handiness 

or portability. All models are equipped with spacious 

upper tables that permit the mitre saw to be easily 

transformed into a disk saw to perform cuts of up to 

40 mm thickness, engraving, facing, and trimming. 

Only one operator is required for the use of the mitre 

saw, which has been designed and constructed in 

compliance with Standard EN 61029. All models are

equipped with release switches featuring LOCK in 

‘ON’ buttons. All models come with minimum voltage 

circuits that prevent the accidental restarting of the 

machine after interruptions in power supply because 

in such cases the operator is always required to reset 

work  conditions;  a  high-power  and  high-efficiency 

asynchronous motor ensures silent operation at all 

rpm levels. The machine also comes with a motor 

brake that permits the blade to be stopped within 10 

seconds of the release of the button on the switch.