background image

 

extinguisher. 

 

Use Only Dry Potholders 

– Moist or damp potholders on hot surfaces may result in burns from steam. 

Do not let potholder touch hot heating elements. Do not use a towel or other bulky cloth. 

 

Make  Sure  Reflector  Pans  or  Drip  Bowls  Are  in  Place 

–  Absence  of  these  pans  or  bowls  during 

cooking may subject wiring or components underneath to damage. 

 

Protective Liners 

– Do not use aluminum foil to line surface unit drip bowls or oven bottoms, except 

as suggested in the manual. Improper installation of these liners may result in a risk of electric shock, 
or fire. 

 

Glazed Cooking Utensils 

– Only certain types of glass, glass/ceramic, ceramic, earthenware, or other 

glazed  utensils  are  suitable  for  range-top  service  without  breaking  due  to  the  sudden  change  in 
temperature. 

 

Utensil Handles Should Be Turned Inward and Not Extend Over Adjacent Surface Units 

– To reduce 

the  risk  of  burns,  ignition  of  flammable  materials,  and  spillage  due  to  unintentional  contact  with  the 
utensil, the handle of a utensil should be positioned so that it is turned inward, and does not extend 
over adjacent surface units. 

 

Do Not Soak Removable Heating Elements 

– Heating elements should never be immersed in water.   

 

Use this appliance only for its intended purpose as described in this 

Owner’s Manual

 
 

- SAVE THESE INSTRUCTIONS - 

 

Summary of Contents for Summit CR430SS

















Reviews: