background image

3

English

Product Profile

This product is built to shred paper, staples, small paper clips
and credit cards

. It is not built to shred adhesive labels, trans-

parencies, newspaper, cardboard, large paper clips, or plastic

(other than credit cards). Attempting to shred items not intended

for this shredder may cause damage.

Strip-Cut

Strip-cut Confetti-cut 

(120-2)

(120-2)

(120C-2)

Sheet capacity*

18-20 sheets

16-18 sheets

12-14 sheets

Paper shred size

5,8 mm

3,9 mm

3,9 x 25 mm

Maximum paper width

241 mm

241 mm

241 mm

Recommended daily capacity

4,000 sheets

4,000 sheets

2,000 sheets

*Based on A4 (70 g/m

2

) paper with shredder operating at rated voltage; heavier paper, high humidity, or other than rated

voltage may reduce sheet capacity. 

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING

While setting up shredder

• Check shredder for damage or defects; some paper particles in the basket are normal

due to product testing and does not indicate a defect. 

• Avoid touching exposed blades on underside of confetti-cut shredder head. 

• Plug power cord in an outlet that can easily be reached. The plug is the primary electri-

cal disconnect. 

• Make sure the electrical rating listed on the serial label (located inside, just below top of

shredder) matches the available electric power.

• Do not place shredder near or over a heat or water source.

While operating shredder

• Keep hands and hanging objects (jewelry, ties, loose clothing, 

long hair, etc.) away from paper entry. 

• Keep children and pets away from the shredder. 

When not in use

• Always turn off and unplug shredder.

• Unplug before emptying basket.

• Do not open shredder head: Danger of electric shock.

Opening shredder head will void the warranty.

NOTE:

Do not use flammable synthetic oil, petroleum-based products or aerosols of any

kind on or near product at any time.

Summary of Contents for 120-2










Reviews: