4
5
Place the air purifier face up on a
flat, stable work surface. Open the
access panel by pressing in latches
on each side of the unit (Fig 3).
Make sure filters are in correct order
- pre-filter / carbon filter / HEPA
filter - and inserted into filter frame
(Fig 16).
IMPORTANT: Make sure filter
detection area aligns with window
in filter frame (Fig 17).
Disconnect main housing assembly
from rear housing assembly.
Separate main housing from rear
housing. Lift main housing assembly
away from rear mounting housing
(Fig 8).
Close front panel by pressing
firmly until both sides latch closed
(Fig 19).
Open access panel and remove
filter assembly by pulling out on
top of side edges of frame, then
lifting. NOTE: remove all plastic
wrap from filters (Fig 4).
The power connector (B, in Fig
12) will carry power from the rear
housing to the main housing once
the assemblies are fully seated. The
main assembly will attach to the rear
housing assembly by the four screws
previously removed (Fig 5 & 6). Two
snap hooks (A, in Fig 12) will hold the
main and rear assemblies together
until the screws can be installed.
Remove the six housing screws (Fig 5 & 6) and set aside for re-assembly.
Carefully align the main assembly
with the rear housing assembly.
Slowly press into place until snap is
heard, and there is no gap between
the assemblies (Fig 13). The unit
should now support its own weight.
At the location of the two upper
housing corner screws (Fig 5), insert
a flat head screwdriver and gently
twist to release tab as shown in Fig
7. This will disconnect main housing
assembly from the rear housing
assembly.
Open front panel by pressing
latches on both sides of unit. Allow
door to open fully. Insert filters
– IMPORTANT: make sure filter
detection window is aligned in
upper right corner (Fig 18).
To restrict access to the control panel
and filters the unit can be locked. To
lock, insert the key provided and
rotate clockwise ¼ turn (Fig 21).
Once the unit is closed re-establish
power. Lights on the control panel will
be visible through the lens, indicating
the unit is operational (Fig 20). The
power light indicator will flash once
a second.
Install six screws (previously removed) to secure main assembly to rear
housing assembly (Fig 14 & 15).
MOUNTING REAR HOUSING AND MAIN ASSEMBLY
RE-INSTALLING FILTERS
LOCKING ACCESS PANEL
MAIN ASSEMBLY INSTALLATION
REAR HOUSING INSTALLATION & WIRING
Test the electrical outlet box first to ensure rated power requirements are met before beginning installation.
Remove air purifier from its shipping carton and remove all packing material.
Reference rear housing and locate desired mounting location. Again, it is strongly recommended at least 2 mounting anchors for the air purifier be mounted to
an existing stud.
WARNING:
To avoid the risk of electrocution confirm the electrical supply has been disconnected or switched off before continuing any installation work.
IMPORTANT:
Make sure all plastic wrap is removed from filters.
Fig 3
Fig 7
Fig 16
Fig 17
Fig 18
Fig 19
Fig 20
Fig 21
Fig 4
Fig 8
Fig 5
Fig 14
Fig 12
Fig 13
Fig 6
Fig 15
Fig 10
Fig 11
1
2
3
4
5
6
1
2
3
4
5
6
Using provided template ensure electrical
outlet box is located behind cable hole (A)
in Rear Housing assembly (Fig 9). Drill
holes and place anchors in wall.
If mounting on concrete, cinder block or
brick type walls route the wires through
the “punch-out” hole marked (B) in Fig 9.
Check for washers at all mounting
screw locations (Fig 10). Pull wires
from electrical outlet box through
hole in rear housing. Align housing
over anchors and securely install all
mounting screws.
Attach wires from electrical outlet box to wires located inside rear housing using wire nuts. Match up line (black) and neutral (white) wires (Fig 11). Make sure
all connections are made in accordance with federal, state and local codes and regulations.
A
B
A
B
A
A
B
Fig 9
AeraMaxPRO_AMIV_InstallGuide_408531_RevB_111314.indd 4-5
11/13/14 11:02 AM
