BASIC SHREDDING OPERATION
BASIC SET UP
ADVANCED PRODUCT FEATURES
3
PRODUCT MAINTENANCE
Ensure access to a
dedicated 15Amp,
120V outlet
R
R
R
R
R
R
R
R
4
1
3
R
R
R
R
R
R
R
R
2
Open the door
R
R
R
R
1
2
3
4
or
5
R
R
Place cutter head into
top of cabinet, use 2
people
Plug in and make
sure door is closed
Press ( ) ON to
activate
When finished
shredding set to
( ) OFF
Feed paper straight
into paper entry and
release
Do nothing and shredder
will automatically shut
off after 30 minutes of
inactivity
Make sure safety flap
is securely in place
SHREDDER SET-UP
All cross-cut and micro-cut shredders require oil for peak performance. If not
oiled, a machine may experience diminished sheet capacity, intrusive noise
when shredding and could ultimately stop running. To avoid these problems,
we recommend you oil your shredder each time you empty your waste bin or
every 15-30 minutes of continuous use.
OILING SHREDDER
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
3
2
*Apply oil
across entry
Press Reverse (R)
Set to Off ( )
and unplug
1
CLEANING AUTO-START INFRARED SENSORS
PAPER JAM
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
Paper detection sensors are designed for maintenance free operation. However, on rare
occasions the sensors may become blocked by paper dust causing the motor to run even if
there is no paper present
(Note: two paper detection sensors are located in the center of the paper entry).
Turn off and unplug
shredder
Locate Auto-start
infared sensor
Clean any contamination
from the paper sensors
1
2
R
R
3
4
Use thin, long-handled
brush to clean sensors.
Make sure brush is clean
and dry
TO CLEAN THE SENSORS
TROUBLESHOOTING
TO SHRED
SilentShred
™
Technology
SilentShred™ noise quality
shreds without noisy disruptions.
Paper Capacity Indicator: When flashing blue, too much paper is inserted. Shredder will
automatically stop and reverse paper. See Paper Jam section.
Bin Full Indicator: When illuminated, the shredder waste bin is full and needs to be emptied.
Use Fellowes waste bag 36054.
R
R
R
R
R
R
R
R
Safety Shield Indicator: When flashing alternatively with On/Off LED, safety shield is
open and shredding will stop. To resume shredding, make sure safety shield is closed.
Door Open Indicator: When flashing alternatively with On/Off LED, the door is open.
To resume shredding, make sure door is closed.
R
R
R
R
R
R
R
R
Overheat Indicator: When flashing alternatively with On/Off LED, shredder requires
a 10-15 minute cool down period. When is blue, resume shredding.
R
R
R
R
R
R
R
R
R
When flashing blue,
too much paper is
inserted. Shredder
will automatically stop
and reverse paper
2
4
Gently pull uncut paper
from paper entry
1
Shred 1 sheet of
paper to clear
cutters. Resume
normal shredding
R
R
R
R
R
R
R
R
3
If necessary, press
Reverse (R) to run
shredder in reverse
and then pull uncut
paper from shredder
Safety Shield
Electronically controlled shield stops
shredder when opened for advanced safety
Auto Shut Off
After 30 minutes of inactivity, shredder
automatically turns off for zero energy
consumption
15
*Only use a non-aerosol vegetable oil in long nozzle
container such as Fellowes 35250
15
30
https://www.supplychimp.com/
