background image

 

16 

 

 

V I I .       I M P O R T A N T   S A F E T Y   I N S T R U C T I O N S   f o r   P O W E R   P A C K  

 

 

WARNING

:   

When  using  electrically  operated  equipment,  basic  safety  precautions 
should always be followed to reduce risk of fire and personal injury.

 

   

 

• Do not incinerate  the  DC  Power  Pack  even  if it is severely  damaged 
   or is completely  worn  out. The  DC Power  Pack  can explode  in a fire. 

 

 

• A small  leakage  of liquid  from the  DC Power  Pack  cells  may  occur under   
    extreme  usage  or temperature  conditions.  This does  not indicate  a failure. 
   However,  if this  leakage  gets on  your  skin: 

 

 

a.   Wash  quickly  with soap and  water. 

 

b.   Neutralize  with a mild  acid such as lemon  juice or vinegar 

 

c.   If the  DC Power  Pack  liquid  gets  into your  eyes, flush them  with clean  water   
        for  a minimum  of 10  minutes  and seek  immediate medical  attention.   

     (MEDICAL  NOTE: The  liquid  is 25%-35% solution  of potassium  hydroxide.)

 

 

 

• Never  attempt  to open the DC Power  Pack  for  any  reason.   
      If the  plastic housing  of the DC Power  Pack  breaks  or cracks,   
      immediately  discontinue  use  and do  not  recharge. 

 

DC  PACK  CELLS

 

 

After  several  years  of  normal  use,  the  cells  in  your  DC  Power  Pack  will  no 
longer accept a charge. This is a normal occurrence, and signifies that the DC Power 
Pack  cells  have  reached  the  end  of  their  useful  life.  Replacement  DC  Power 
Packs  are  available  from  Feltest,  order part No. UPN  77-1055. 

 

Your  DC  Power  Pack  contains  nickel  cadmium  cells.  The  Environmental  Protection 
Agency considers cadmium to be a toxic material that can do severe damage to the 
environment.  Check  with  your  state  Environmental  Protection  Agency  to  find  out 
how to properly recycle or dispose of your DC Power Pack. 
 

 

Summary of Contents for PowerStrobe





























Reviews: