1. LINE CORD - Connect the power line cord to a
g rounded AC receptacle in accordance with the
voltage and frequency ratings as listed on the rear
panel of the Prosonic amplifier.
2. POWER SWITCH - Turns the AC power on and off.
3. FUSE - Located in the AC supply of the amplifier, the
fuse helps protect the unit from electrical fault or tube
failure. Replace a failed fuse with the same type and
rating. If the amplifier repeatedly blows fuses, take it
to an authorized Fender service center.
4. S TANDBY SWITCH - Switches the unit between
operate and stand-by modes when the power switch is
ON. In stand-by mode, no sound will be heard from the
amplifier but power is still supplied to the tube
filaments keeping them warm and the unit ready to
play. Use this switch during short breaks to increase
tube life. Wait at least 50 seconds after the power
switch is on before putting the unit into the standby
mode.
5. RECTIFIER/BIAS SWITCH - Allows for the selection of
rectifier sounds and bias classes to best suit your
playing style (experiment to find a preferred setting).
The (1) TUBE A setting at low volume sounds much like
the (2) TUBE AB2 and (3) S.S. “solid state” AB2
settings at high volume.
6. IMPEDANCE SWITCH (Head only) - Sets the output
impedance of the amplifier to match the speaker
impedance for maximum power and tube life.
7. SPEAKER (Combo), SPEAKER 1 (Head) - Primary
output jack for connection to speakers. A speaker
must always be connected at this jack for the unit to be
heard.
8. EXTERNAL SPEAKER (Combo), SPEAKER 2 (Head) -
Output jack for connection to an external speaker.
ONLY use in conjunction with the main speaker jack.
Using this jack on the Combo automatically switches
the amplifier impedance to 8
Ω
.
9. FOOTSWITCH - Jack for connection to the included
footswitch. The footswitch allows remote switching
between channels as well as ON/OFF switching of the
REVERB effect on the
combo
unit only.
10.EFFECTS RETURN - Connect cord from extern a l
effects devices at this input jack. Inserting a plug at
this jack automatically disconnects the unit’s internal
connection from the pre-amp to the power amp.
11.EFFECTS SEND - Connect cord to external effects
devices at this output jack. This jack can also be used
as a line out.
R
R
e
e
a
a
r
r
P
P
a
a
n
n
e
e
l
l
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
s
s
S
S
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n
s
s
1
2
3 4
5
6
7
8
9
10
11
PART NUMBER* - COMBO:
021-1077-x00 (100V)
021-1007-x00 (120V)
021-1047-x00 (230V) UK
021-1067-x00 (230V)
021-1037-x00 (240V) Aust
021-1087-x00 (230V) Nordic
SPEAKER ENCLOSURE:
2-10” Custom Design Celestion
®
speakers
PART NUMBER* - HEAD:
021-2077-x00 (100V)
021-2007-x00 (120V)
021-2047-x00 (230V) UK
021-2067-x00 (230V)
021-2037-x00 (240V) AUSTRALIA/ NZ
POWER REQUIREMENTS:
360W.
COMPANION SPEAKER ENCLOSURE:
4 12” Celestion
®
Vintage 30 speakers:
021-3001-100 (RED)
021-3001-200 (GREEN)
021-3001-000 (BLACK)
POWER OUTPUT:
Class AB2, Solid state rectifier: 60 W R.M.S. (minimum into 8 or 16
Ω
)
Class AB2, 5AR4/GZ34 rectifier: 50 W R.M.S. (minimum into 8 or 16
Ω
)
Class A, 5AR4/GZ34 rectifier: 30 W R.M.S. (minimum into 8 or 16
Ω
)
OUTPUTIMPEDANCE:
8
Ω
or 16
Ω
(Combo), 4
Ω
, 8
Ω
or 16
Ω
, (Head).
INPUTIMPEDANCE:
1 M
Ω
TUBES:
COMBO
HEAD
Two (2)
Two (2)
5881/6L6WGC
(P/N 099-5090)
Five (5)
Four (4)
12AX7A
(P/N 099-5091)
One (1)
None (0)
12AT7
(P/N 099-5092)
One (1)
One (1)
5AR4/GZ34
(P/N 099-5097)
FUSE TYPE:
100/120V units: T3 Amp/250V,
230-240V version T1.6 Amp 250V
DIMENSIONS:
COMBO
HEAD
HEIGHT:
18.5 in
(47 cm)
9 in.
(23 cm)
WIDTH:
24 in
(61 cm)
24 in.
(61 cm)
DEPTH:
10.5 in
(26.5 cm)
9.5 in.
(24 cm)
WEIGHT:
48 lbs.
(22 kg)
42 lbs.
(19 kg)
*For Prosonic COLOR DESIGNATED part number, replace “x” with: 1 = RED, 2 = GREEN, 0 = BLACK (Combo Only)
Product specifications are subject to change without notice.
