Fenwal Controls 35-608 Series Installation Instructions Manual Download

Page: 8 / 8

Fenwal Controls
400 Main Street
Ashland, MA 01721
Tel. (508) 881-2000

Kidde-Fenwal Inc. 06-237657-001

Rev A

EU DECLARATION OF CONFORMITY

Company Name:

Kidde-Fenwal Inc.

Postal Address:

400 Main Street

City and Post Code:

Ashland, MA 01721

Tel:

508-881-2000

Declare that the DoC is issued under sole responsibility and belongs to the following product:

Apparatus Model(s)

Series 35-40, 35-53, 35-60, 35-61, 35-63, 35-608, 35-65, 35-66, 35-9X

Type:

Fitting

Batch Number

Date code and Revision Level Assigned per production lot, (YYWW RR)

Object of the Declaration:

Series 35-40, 12/24Vdc Direct Spark Automatic Gas Ignition Controllers
Series 35-53, 12Vdc Direct Spark Automatic Gas Ignition Controllers
Series 35-60, 35-61, 35-63, 35-608 24Vac Direct Spark Automatic Gas Ignition
Series 35-65 & 35-66 24Vac Hot Surface Automatic Gas Ignition Controllers
Series 35-9X Platform Ignition Module

SERIES 35-40

SERIES 35-53

SERIES 35-60/61/63/608

SERIES 35-65/66

SERIES 35-9X

The object of the declaration described above is in conformity within the relevant union
harmonization legislation:

Gas Appliance Regulation

(

EU) 2016/426

Low Voltage Directive:

2014/35/EC

EMC Directive:

2014/30/EC

Rohs

2011/65/EU

The following harmonized standards and technical specifications have been applied:

EN298:2012:

Automatic Burner Control systems for Burners and appliances burning gaseous or liquid fuels.

EN13611:2007_A2:2011:

Safety and control devices for Gas Burners and Gas burning appliances – General Requirements.

Name of Notified Body & Number:

BSI Group, 0086, EU Type Examination Certification

Notified Body Certificate No.:

Series 35-40:

CE682407

Series 35-53

CE682404

Series 35-60/61/63/608

CE682405

Series 35-65/66

CE682406

Series 35-9x

690652

Surveillance Audit Notified Body:

BSI Group

For copies of the Installation Instructions and the EU DoC, got to

www.fenwalcontrols.com

, - Document Library - Data sheets.

Paul Finn

Kidde-Fenwal, Inc. Ashland, MA USA

Oct

2018

Paul Finn, Certification Engineer

Place of Issue:

Date of Issue

Name

Summary of Contents for 35-608 Series









Search results

Summary of Contents for 35-608 Series

Reviews:

Related manuals for 35-608 Series

Brands by name

Popular brands

Fenwal Controls 35-608 Series, Installation Instructions Manual

Search results

Summary of Contents for 35-608 Series

Reviews:

Related manuals for 35-608 Series

Brands by name

Popular brands