36
7.6 PRECISION ADJUSTMENT OF THE
STOP FOR 45ºMITRE CUTS (FIG. 2/4/8)
• Lower the machine head and fix with the lock pin.
• Fix the rotary table in 0ºposition.
• Undo the locking nut and, holding the handle, tilt the
machine head to the left by 45º
• Place the 45ºstop angle between the saw blade and
the rotary table.
• Slacken the counter nut and adjust the setting screw
until the angle between the saw and the rotary table
equals exactly 45º.
• Re-tighten the locking nut and make the cut as des
-
cribed in Section 7.2.
7.7
MITRE CUTS 0º-45ºAND ROTARY
TABLE 0º-45º (FIG. 4/9)
The KGSZ4300 can be used to make mitre cuts on
the left at an angle of 0º-45º relative to the work top
and 0º-45ºrelative to the stop rail.
• Lift the machine head to its top position
• Release the turntable by loosening the locking grip.
• Adjust the rotary table by its handle to the required
angle (see also Section 7.4).
• Re-tighten the locking handle to fix the rotary table
in position.
• Undo the clamping nut and, holding the handle, tilt
the machine head to the left to the required angle
dimension (see also Section 7.5).
• Re-tighten the locking nut and make the cut as des
-
cribed in Section 7.2.
7.8 CHIP EXTRACTION (FIG.1)
The saw is equipped with a chip collection bag. The
chip bag can be emptied by opening zip fastener at the
bottom.
7.9 REPLACING THE LAW BLADE (FIG. 11)
• Pull out the power plug.
• Swing up the machine head.
• Press the lever and swing up the saw blade guard to
the point where the recess in the saw blade guard is
above the flange bolt.
• Press the saw shaft lock with one hand while hol
-
ding the wrench on the flange bolt with the other.
• Firmly press on the saw shaft lock and slowly rotate
the flange bolt in clockwise direction. The saw shaft
lock engages after no more than one rotation.
• Now, using a little more force, slacken the flange
bolt in clockwise direction.
• Turn the flange bolt until it is completely removed.
• Take the blade off the inner flange and pull out
downwards.
• Mount the new saw blade in reverse order and
fasten.
• Important! The cutting bevel of the teeth, i.e. the
direction of rotation of the saw blade, has to con-
form with the direction of the arrow marked on the
housing.
• Clean the saw blade flanges thoroughly before
mounting the saw blade.
• Reattach the movable blade guard in reverse order.
• Before using the saw again, check that the safety
devices are in good working order.
• Important: Every time that you change the saw
blade, check to see that it spins freely in the groove
of the turntable in both perpendicular and 45º angle
settings.
7.10 LASER FUNCTION (FIG. 12)
• You can switch the laser ON and OFF with the
switch.
• The laser directs a beam onto the workpiece.
• Extremely precise cuts can be made using the laser
function.
8. MAINTENANCE
• Keep the machine’s air vents unclogged and clean at
all times.
• Remove dust and dirt regularly from the machine.
Cleaning is best done with compressed air or a rag.
• Re-lubricate all moving parts in regular intervals.
• Never use caustic agents to clean plastic parts.
Summary of Contents for 19144-0106
