63
Read the following
WARNING
label found on the front of the
sander:
WARNING
1. Read manual before using sander.
2. Wear safely goggles.
3. Wear a dust mask.
4. Maintain 1/16” maximum clearance between table and sanding
belt and disc.
5. Always support workpiece with “backstop” or “worktable”.
6. Avoid “Kickback” (workpiece thrown at you) – use only the
left half of the disc.
7. Avoid fire. Clean out all sawdust and disconnect from any
vacuum before sanding metals.
WHEN INSTALLING OR MOVING
THE SANDER
AVOID DANGEROUS ENVIRONMENT. Use the sander in
a dry, indoor place protected from rain. Keep work area well
lighted.
Place the sander so neither the user nor by standers are forced to
stand in line with the abrasive belt or disc.
To avoid injury from unexpected sander movement:
• Always unplug the sander before moving it.
• Put the sander on a firm level surface where there is plenty of
room for handing and properly supporting the workpiece.
• Support the sander so it does not rock.
• Bolt the sander to its work surface. Use the fasteners and
method shown in “Assembly and Alignment.” (Page 7)
•
NEVER STAND ON TOOL.
Serious injury could occur if the
tool tips. Do not store anything above or near the tool where
anyone might stand on the tool to reach them.
BEFORE EACH USE:
Inspect your sander.
DISCONNECT THE SANDER.
To avoid injury from accidental starting, unplug the sander, turn
the switch off and remove the switch key before changing the
setup, sanding disc or belt or adjusting anything.
CHECK DAMAGED PARTS.
Check for:
• alignment of moving parts,
• binding of moving parts,
• broken parts.
• work parts that cause a gap larger than 1/16” between work
support and sanding surface.
• sanding belt narrower than 4 inches. Narrower belts uncover
parts that could trap your fingers,
• worn or damaged electric cords,
• stable mounting, and
• any other conditions that may affect the way the sander works.
If any part is missing, bent, or broken in any way, or any electrical
parts don`t work properly, turn the sander off and unplug the
sander.
REPLACE
damaged, missing, or failed parts before
using the sander again.
MAINTAIN TOOLS WITH CARE.
Keep the sander clean for
best and safest performance. Follow instructions for lubricating.
REMOVE ADJUSTING KEYS AND WRENCHES
from tool
before turning it on.
Safety instructions for belt and disc sander
Safety is a combination of common sense, staying alert and
knowing how your belt and disc sander works. Read this manual
to understand this sander.
BEFORE USING THE SANDER
WARNING:
To avoid mistakes that could cause serious,
permanent injury, do not plug the sander in until the
following steps are completed.
• Assembly and alignment. (See pages 7-11)
• Learn the use and function of the ON-OFF switch, backstop,
belt tracking knob, belt tension lever, work table and work table
tilt lock knob. (See pages 12-13)
• Review and understanding of all safety instructions and
operating procedures in this manual.
• Review of the maintenance methods for this sander. (See pages
19-20)
ENGLISH
CONTENT
Specifications .............................................................................. 63
Safety instruction ........................................................................63
Before using the sander ...............................................................63
When installing or moving the sander ........................................63
Whenever sander is running ........................................................65
Unpacking and check contents ....................................................65
Assembly.....................................................................................66
Getting to know your belt and disc sander ..................................69
Basic operation ............................................................................70
Lubrication ..................................................................................73
Trouble shooting .........................................................................75
Wiring Diagram ........................................................................115
Exploded view + Part list ..........................................................116
EC Declaration of conformity ...................................................117
FOR YOUR SAFETY:
READ ALL INSTRUCTIONS CAREFULLY
• Mounting • Operation • Spare parts
SPECIFICATION
Belt dimension ............................................ mm
100 x 915
Belt speed .....................................................m/s
8
Disc diameter .............................................. mm
150
Disc speed ........................................... apgr/min
2850
Noise ....................................................... dB(A)
85
Motor...............................................................V 230
1-vinf
ā
zes
Motor..............................................................W 400
Weight ........................................................... kg
17
Original instructions
