USER MANUAL
Patented product, counterfeiting not allowed.
Shenzhen FEREI Lighting Co., Ltd
.
3rd Industrial Zone, Xiakeng Village, Tongle, Longgang District, Shenzhen 518116, China.
TEL: 0086 755 8480 7942 / 0086 755 8480 7943
FAX: 0086 755 8480 7944.
E-mail: ferei@ferei.com
•
Website: www.ferei.com
HL40AA II PRODUCT SPECIFICATIONS
LED
CREE XML2 COOL WHITE
ANSI/FSC
MAX
CUSTOMIZED SETTING
POLICE
STROBE
SLOW
STROBE
FAST
STROBE
SOS
LIGHT PER 100% 10% 20% 30% 40% 50% 60% 70% 80%
USERDEFINED
OUTPUT LM 1000 100 200 300 400 500 600 700 800
USERDEFINED
RUNTIME H
16
160
80
57
40
32
27
23
20
>16
RANGE M
OVER 200 METERS
MAXIMUM
INTENSITY
23256 CD
LED
CREE XML2 NEUTRAL WHITE
ANSI/FSC
MAX
CUSTOMIZED SETTING
POLICE
STROBE
SLOW
STROBE
FAST
STROBE
SOS
LIGHT PER 100% 10% 20% 30% 40% 50% 60% 70% 80%
USERDEFINED
OUTPUT LM 930
93
186 279 372 465 558 651 744
USERDEFINED
RUNTIME H
16
160
80
53
40
32
27
23
20
>16
RANGE M
OVER 150 METERS
MAXIMUM
INTENSITY
5625 CD
WATERPROOF
RATING
IPX4
ANTIDROP
1M
DIMENSION
30 MM HEAD DIAMETER
BATTERY
3 X AA BATTERIES
WEIGHT
168 G EXCLUDING BATTERY
NOTE: THE ABOVE PARAMETERS WERE TESTED BY USING THE AA LR6
HIGH POWER CAPACITY BATTERY
INTELLIGENT TEMPERATURE CONTROL INSTRUCTIONS
This product is designed with a temperature control circuit.
The LED is a heating device that is sensitive to temperatures,
especially high levels of power and brightness. High temperatures
will easily damage or shorten the life of the LED. Ferei designs its
products with an intelligent temperature-control circuit. It measures
the temperature within the LED filament. As the structure of the
lamp differs, the thermal conductivity of the entire lamp is not the
same. In general, the constant surface temperature of the lamp is
50˚C to 60˚C. When it exceeds its programmed temperature, it will
automatically reduce its power to cool down , and the brightness
decreases by small steps. After cooling-down (provided that battery
voltage is sufficient) the power with brightness increases again.
The process of improving its brightness is relatively discrete and will
not produce a flashing effect.
This stepping goes cyclically to maintain the user's safety and the
light's functionality. In conditions of good air-cooling the lamp
delivers light without stepping down even in high levels brightness
mode. There are no preset timers for stepping, but real-time active
temperature measurements, So the actual runtime of the lamp base
on active temperature control to faster or slower battery discharge,
may be slightly longer or shorter runtime than the lamp of data
provided .
WARM TIPS
In order to avoid accidents, please pay attention to the following
tips:
•
Never use damaged, discolored or leaking batteries.
•
Never use batteries with a damaged sleeve or foil covering.
•
Always use 18650 batteries with safety certificates.
•
If the light gets unusually hot when in use, turn it off and check
battery appearance.
•
Never store the battery into the battery holder.
•
Recharging is finished when the LED indicator turns to green.
•
The battery remains at a normal temperature during
recharging. If it gets unusual hot, stop recharging and take the
battery out.
•
Do not dissemble the charger kit by yourself if the battery
couldn’t be recharged.
•
The battery can be used at any time once being recharged. If
it is left unused for long periods, it should be recharged for 4
hours every three months. After being charged they should be
slightly discharged for 10-20 minutes before storage.
•
Be sure to always recharge the battery in a safe place and do
not leave unattended while charging.
MAINTENANCE
1
Wipe the glass lens with a soft cloth at regular intervals to
ensure maximum light transmittance (avoid using corrosive
detergents).
2
Ensure the cable plug and inside of the battery box remain free
of dirt and debris.
3
Unplug the cable from the battery box when unused for
extended periods.
WARNING
•
It is a lighting tool, not a toy. Keep it away from children.
•
Should not be aimed directly at the eyes of humans or animals
•
Do not place the light face / lens down when turned on.
•
The surface of the flashlight may become hot during extended use.
•
Do not dismantle or dissemble any structural parts of the light, especially
the seal parts.
•
Dry the light surface with soft cloth immediately after exposure to water or
any corrosive substance.
•
Always remove batteries during long periods of inactivity (more than 30
days).
•
Ferei reserves the right of interpretation of this manual.
Focusing
LED Headlamp
HL
40
AA
II
