7
EN
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm2. When using a cable
reel always unwind the reel completely.
3. ADJUSTING THE MACHINE
Adjusting the cutting depth
Fig.B
• Move the motor housing (3) as far as possible
backwards.
• Set the cutting depth by turning the cutting
depth adjustment knob (9).
• The markings on the depth adjustment knob
(9) correspond to the biscuit dowel size being
used (16).
• You can fine adjust the cutting depth setting by
turning the depth fine adjustment screw (10).
• Move the motor base forwards and check if
depth fine adjustment screw (10) will fall in the
notch of the adjustment knob.
The following table shows the relationship of
the markings on the adjustment knob to cutting
depth, thickness of material and associated
biscuit dowel.
Marking
Thickness
Biscuit
Cutting
of material
Dowel
depth in mm
0
8-12 mm
No. 0
8.0
10
12-15 mm
No. 10
10.0
20
> 15 mm
No. 20
12.3
Max. -
- 14.0
Adjusting the cutting angle
Fig. A + G
The cutting angle can be set the following way:
• Release the angle adjustment knob (6) by
turning it anti-clockwise
• The set angle is shown on the scale (21) below
the knob (6)
• After setting to the right angle, tighten the
knob (6) again by turning it clockwise.
Adjusting the height to match material
thickness
Fig. B
The correct height can be set the following way:
• Release the height adjustment knob (8) by
turning it anti-clockwise
• The set height is shown by the scale and the
arrow (22).
• After setting to the right height, tighten the
knob (8) again by turning it clockwise.
The height must correspond to half of the material
thickness of the working piece, the groove for the
biscuit dowel must always be in the middle of the
working piece.
4. MOUNTING ACCESSORIES
Prior to mounting an accessory always
unplug the tool.
How to change the saw blade
Your machine is delivered with the saw
blade already assembled on the machine
Fig. C & D
• Put the machine in upside-down position and
remove the 4 screws on the bottom plate by
using a screw driver (not included)
• Remove the bottom plate (20)
• Press the spindle lock (5) and turn the spindle
until it engages in the lock. Keep the spindle
lock pressed during this procedure.
• Remove the flange nut (17) from the spindle
by using the spanner (14) and turn it
counterclockwise.
• Position the saw blade (18) on the flange (17).
• Be aware that the arrow on the sawblade
indicates the same direction as the arrow on
the inside of the housing.
• Place the flange nut (17) on the spindle and
tighten it with the wrench.
• Take care the flange nut (17) will be placed the
correct way: The collar side must fit inside the
saw blade bore, the flat side must be pointing
upwards.
• Release the spindle lock and check that the
spindle is unlocked by rotating it.
• Assemble the bottom plate (20) again and fix
the 4 screws.
Summary of Contents for BJM1009
