Ferm
39
POSITIONING OF THE MACHINE
Based on the size of the workpieces the machine can be
positioned in several ways.
LARGE WORKPIECES
Fig. G
•
Place the machine near the workpiece.
•
The middle of the base plate (this point is marked on
the base plate) must facing the centre of the groove in
the workpiece (see marking the workpiece).
SMALL WORKPIECES
Fig. H
•
Place the machine near the workpiece.
•
The side of the machine must be facing the side of the
workpiece.
WORKPIECESTHINNER THAN 16 MM
Fig. I
•
Place the machine near the workpiece.
•
Place the adjustment plate (5) on the angle stop (4).
•
Take care for setting the height, the groove for the
biscuit dowel must be in the middle of the workpiece.
For workpieces thinner than 16mm it is not possible to
make the groove for the biscuit dowel in the middle of
the workpiece without the aid of the adjustment plate.
SAWING GROOVES
•
Move the motor base backward.
•
Place the machine near the workpiece.
•
Position the machine (see positioning of the
machine)
•
Hold the machine with both hands and switch the
machine on.
•
Push the motor base carefully forward as far as
possible.
•
Move the motor base backward and switch the
machine off.
JOINING THE WORKPIECES
When the grooves in both workpieces have been made
the workpieces can be joined together:
•
Put glue in both grooves.
•
Place the biscuit dowel in the groove of one
workpiece.
•
Place the other workpiece on the biscuit dowel.
•
Fasten the workpieces and wait till the glue is dry.
CHECKING THE CUTTING DEPTH
Fig. J
Always check the cutting depth after mounting a
saw blade:
•
Disconnect the plug from the socket.
•
Move the motor base (15) as far as possible back-
wards.
•
Set the cutting depth in the maximum position by
turning the depth adjustment knob (7).
•
Move the motor base forwards till the pin (A) will fall
in the notch of the adjustment knob (7).
Turn the saw blade till one tooth of the saw blade is in
the front position.
•
Measure the distance from the side of the base plate
to the tooth of the saw blade
•
Check if the distance is 18 mm. the maximum
position is 18 mm.
SETTING THE CUTTING DEPTH
When the cutting depth is not correct, it can be adjusted
as following:
•
Move the motor base (15) as far as possible
backwards.
•
Loosen the pin (A).
•
Set the cutting depth by turning the screw, the screw
is positioned at the back of the pin (A).
•
Repeat the procedure till the cutting depth is correct
•
Fasten the pin (A).
MAINTENANCE
Make sure that the machine is not live and
unplugged when carrying out maintenance work
on the motor.
The Ferm machines have been designed to operate over
along period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper machine care and regular cleaning.
Cleaning
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt. If the dirt does not come off use a soft
cloth moistened with soapy water. Never use Solvents
such as petrol, alcohol, ammonia water, etc. These
solvents may damage the plastic parts. Keep the moving
parts of the machine clean, like the guiding pillars, the
mechanism of the heigt adjustment and angle
adjustment, to ensure good working.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part, please
contact your local Ferm dealer.
In the back of this manual you find an exploded view
showing the parts that can be ordered.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of
the packaging materials can be recycled. Take these
materials to the appropriate recycling locations.
6
Ferm
