$
. ' ,
$ .
•
*
+ .
•
/ /&3
5
!
•
* +
. 7
$
!
. *
. 8
.
,
$
.
•
9
. 3
. * !
.
•
.
: $
.
9
.
•
: $
. 9
$. 7
. 9
. *
.
. 1
* (3)
. <:
> (7)
.
. /
(8)
.
. 1
/
0# 45#. >
(5),
(1)
.
> (5)
.
,
•
7
:
. B .
!. 9
! .
. >!$
.
. > ,
$
.
•
&
. &
,
. 3
$. 9
$. 3
$ .
!!
.
•
7
$.
•
& :
180mm.
•
*
.
•
B!
.
•
#
! (. 2):
. B .
!. 9 (4, . 1)
.
. >
.
. >
(4, . 2).
. 9 (3, . 2)
(2, . 2),
(1, . 2).
. $
(3, . 2).
Ferm
41
MITRE GUIDE
Fig.1
The mitre guide has a variable setting between 0° and
45°. Loosen the knobs (5), set the mitre by tilting the
table (1) up until you have reached the required tilt. Tigh-
ten the knobs (5) again on both sides of the work table.
CLEANING, MAINTENANCE AND REPAIR
•
Please clean the tool immediately after use:
a. Disconnect the plug from the socket.
b. Remove the water tray from the machine and
drain the dirty water.
c. Unscrew the splash guard and clean it.
d. Loosen the star-shaped knob, fold up the table,
and polish the entire machine.
•
The machine complies with all current safety regula-
tions. Repairs may only be carried out by an approved
company, because repair attempts by unqualified
people may cause injuries to the user and bystanders.
Regularly check the plug and the cable and if they are
damaged they should be replaced by an approved
company. Also check any extension cables. Damaged
safety guards and switches must be replaced before
the machine is used again.
CHECKING AND REPLACING THE DIA-
MOND BLADE
•
Cracked or distorted diamond blades must be
replaced.
•
Type of disk: a diamond blade with a diameter of
180mm.
•
Do not use diamond blades that do not meet the spe-
cifications in these instructions.
•
Ensure that the diamond blade is secured properly
and rotates in the correct direction.
•
To replace a worn disk, please take the following
steps (fig. 2):
a. Disconnect the plug from the socket.
b. Remove the water tray (4, fig. 1) from the
machine.
c. Loosen the splash guard’s fixing bolts and
remove the splash guard.
d. Loosen the blade fixing nut (4, fig. 2).
e. Remove the counter flange (3, fig. 2) and blade
(2, fig. 2) and push the new blade on the flange (1,
fig. 2). Consider the rotation direction indicated
on the blade. Attach the counter flange (3, fig. 2).
f. Tighten the fixing nut (4, fig. 2) and the splash
guard.
g. Ensure you do not leave any tools lying on the
splash guard.
OLD ELECTRICAL TOOLS AND THE ENVI-
RONMENT
If your electrical tools have been used so intensively that
they need to be replaced or if you no longer use them,
please consider the environment when you dispose of
them. Electrical equipment should not be discarded with
household waste, but should be recycled. For more
information, please contact your local service centre.
GUARANTEE
The guarantee terms can be found on the enclosed guar-
antee card.
For any questions in relation to parts and accessories,
please contact our service centre on
We declare under our sole responsibility that this pro-
duct is in conformity with the following standards or
standardized documents
EN61029-1, EN55014-1, EN55014-2
EN61000-3-2, EN61000-3-3
in accordance with the regulations.
98/37/EEC
73/23/EEC
89/336/EEC
from 01-01-2004
ZWOLLE NL
W. Kamphof
Quality department
CE
ı
DECLARATION OF CONFORMITY
(UK)
4
Ferm
