3
EN
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class ll machine. Your machine is double
insulated; therefore no earthwire is
required.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
3. OPERATION
Always observe the safety instructions
and applicable regulations.
This glue gun (kit) has been especially designed
for glueing products such as wood, plastic, foam,
rubber, fabric, cardboard, tiles, ceramics, etc.
Quickly setting, the glue is perfect for repairing
carpets, bookbinding, fixing soles, etc. The glue is
waterproof and resistant to the action of many
liquids. The glue gun is quick, environmentally-
friendly, energy-saving and together with the glue
facilitates and quickens any job.
Due operating the glow gun
• The normal setting time of the hot glue is 30
seconds. After 30 seconds the glue starts to
set. Having applied the glue on the relevant
surfaces, wait 15 - 20 seconds before joining
them.
After about 1 minute the joint has reached
90% of its adhesive strength.
• The setting time can be extended to 50 to 60
seconds by applying the glue in thick drops or
shortened by applying the glue in short, fine
lines.
• Joining large surfaces is difficult, as the glue
tends to set before the entire surface has been
covered with glue.
• Preheating the surfaces to be joined
guarantees a strong joint. Sun rays have the
same impact.
• The glue melts from a temperature of approx.
140°C and must never be used on material
that is sensitive to heat.
• The glue gun can be used to replace nails,
paper tape, liquid glue, but not for heavy-duty
jobs.
• The electric glue gun features accurate
temperature control. It is fitted with a special
design feed system that ensures no glue is left
behind inside the mechanism.
• The glue gun requires Ø 12mm glue
cartridges.
• The glue gun comes standard with a bracket
that enables you to put the gun safely on the
table when it is not used.
Operation
• Plug in the tool.
• Insert a glue cartridge into the gun, two when
using it for the first time.
• Wait 5 minutes for the glue to heat.
• Squeeze the trigger to release the glue.
• Replace the glue cartridge as soon as you
notice little if any glue is released from the
gun.
• Disconnect the tool if you do not intend to use
it for some time.
Replacing the nozzle
• Loosen the orange nozzle. If it does not come
easy, use the spanner provided.
• Fit the nozzle on the glue gun. Tightly secure
with the spanner.
Before removing the nozzle, allow the
glue gun to cool down completely to
avoid injuries. Always disconnect the
tool.
4. SERVICE AND
MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
This machine has been designed to operate over
a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Summary of Contents for GGM1001
