7
EN
7. Saw shoe
8. Allen screw for parallel guide
9. Scale for mitre angle
10. Dust extraction connection
11. Grip
12. Allen key
13. Allen key holder
ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Mounting and removing the saw blade (fig. B)
Refer to the table below to select the required saw
blade.
Saw blade
Material
Coarse
Wood
Medium
Wood
Fine
Steel, aluminium, plastic
Very fine
Wood (curves)
Do not attempt to remove the guard from
the machine.
Mounting
• Raise the guard (5).
• Slacken the Allen screws (14) using the Allen
key (12).
• Insert the saw blade (15) in the saw blade
holder (6) as far as possible. The teeth of
the saw blade (15) must point upward and
forward. The smooth side of the saw blade
must engage in the slot of the guide roller (16).
• Tighten the Allen screws (14) using the Allen
key (12).
• Lower the guard (5).
Removing
• Raise the guard (5).
• Slacken the Allen screws (14) using the Allen
key (12).
• Remove the saw blade (15) from the saw blade
holder (6).
• Tighten the Allen screws (14) using the Allen
key (12).
• Lower the guard (5).
Mounting and removing the parallel guide
(fig. C)
The parallel guide is used for sawing along edges
at a maximum distance of 16 cm.
Mounting
• Slacken the Allen screws (8) using the Allen
key (12).
• Insert the parallel guide (17) into the saw shoe
(7).
• Set the parallel guide (17) to the required
position.
• Tighten the Allen screws (8) using the Allen key
(12).
Removing
• Slacken the Allen screws (8) using the Allen
key (12).
• Remove the parallel guide (17) from the saw
shoe (7).
• Tighten the Allen screws (8) using the Allen key
(12).
USE
Switching on and off (fig. A)
• To switch on the machine, press the on/off
switch (1).
• To switch the machine to continuous mode,
keep the on/off switch (1) pressed and
simultaneously press the lock-on button (2).
• To switch off continuous mode, press the on/
off switch (1) again.
• To switch off the machine, release the on/off
switch (1).
Setting the speed (fig. A)
The speed adjustment wheel is used for setting
the speed. The speed adjustment wheel can be
set to 6 positions. The ideal speed depends on
the profile and the teeth of the saw blade and on
the material to be worked.
Do not set the speed during use.
• Turn the speed adjustment wheel (3) to the
required position.
- For hard materials, use a saw blade with fine
Summary of Contents for JSM1023
